User manual JVC KS-FX12WT

[. . . ] CASSETTE RECEIVER KS-FX12/KS-FX12WT RECEPTOR-REPRODUCTOR DE CASSETTE KS-FX12/KS-FX12WT RADIOCASSETTE KS-FX12/KS-FX12WT For installation and connections, refer to the separate manual. Para la instalación y las conexiones, refiérase al manual separado. Pour l'installation et les raccordements, se référer au manuel séparé. For customer Use: Enter below the Model No. which are located on the top or bottom of the cabinet. [. . . ] · Preset stations are erased when the power supply to the memory circuit is interrupted (for example, during battery replacement). If this occurs, preset the stations again. 6 You can easily tune into a preset station. Remember that you must store stations first. If you have not stored them yet, see page 5 or 6. 2 1 1 FM FM1 FM2 FM3 AM AM Select the band (FM1, FM2, FM3 or AM) you want. 2 Select the number (1 ­ 6) for the preset station you want. 7 ENGLISH Tuning into a preset station ENGLISH Other convenient tuner functions SEL MO/RND +/­ T S RPT/SCAN Scanning broadcast stations When you press RPT/SCAN while listening to the radio, station scanning starts. Each time a broadcast is tuned in, scanning stops for about 5 seconds (tuned frequency number flashes on the display), and you can check what program is now being broadcast. If you want to listen to that program, press the same button again to stop scanning. Selecting FM reception sound When an FM stereo broadcast is hard to receive: Press MO/RND while listening to an FM stereo broadcast. The sound you hear becomes monaural but reception will be improved. Lights when receiving an FM broadcast in stereo \ To restore the stereo effect, press the same button again. Changing the AM/FM channel intervals When using this unit in an area other than North or South America: When this unit is shipped from the factory, the channel intervals are set to 10 kHz for AM and 200 kHz for FM. You can change the channel intervals by following the procedure below. 1 Press SEL (select) for more than 2 seconds. "CLOCK H, " "CLOCK M" or "AREA" appears on the display. 2 If "AREA" does not appear, press 3 Press +. "AREA EU" appears and the channel intervals are set to 9 kHz for AM and 50 kHz (for manual tuning) / 100 kHz (for searching) for FM. To reset to the factory setting, follow the above step 1 and 2, then press ­ in step 3 ("AREA US" appears on the display. ) AREA EU: Select this when used in an area other than North and South America. AREA US: Select this when used in North or South America. 8 TAPE OPERATIONS 2 1 3 ENGLISH Tape direction Listening to a tape 1 /I/ATT Turn on the power. 2 Insert a cassette. When one side of the tape reaches its end during play, the other side of the tape automatically starts playing. (Auto Reverse) 3 PROG Select the tape direction. · Press the both buttons at the same time. Each time you press the button, the tape direction changes ) and reverse ( ). alternatively ­ forward ( Press 0. Tape play stops and the cassette ejects from the cassette compartment. · You can also eject the cassette with the unit turnd off. To stop play and eject the cassette To fast-wind a tape Press either ¡ or 1. The tape will be wound in the direction of the arrows (¡ or 1). [. . . ] · Do not store tapes in the following places: ­ Subject to direct sunlight ­ With high humidity ­ At extremely hot temperatures CAUTIONS: · Do not play the tapes with peeling labels; otherwise, they can damage the unit. · Tighten tapes to remove slack since loose tape may become entangled with the mechanism. · Do not leave a cassette in the cassette compartment after use, as the tape may become slack. How to reset your unit Press and hold both the SEL (Select) and (Standby/On/ATT) buttons at the same time for several seconds. This will reset the built-in microcomputer. [. . . ]