User manual JVC KS-FX433

[. . . ] CASSETTE RECEIVER CASSETTEN-RECEIVER RADIOCASSETTE RADIO/CASSETTESPELER KS-FX433R Detachable ATT 35W x 4 0 CD CHANGER CONTROL PROG KS-FX433R TP/RDS SOUND MO RND DISP SEL SSM PTY 7 8 9 10 11 12 CD-CH AM FM For installation and connections, refer to the separate manual. Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch. Pour l'installation et les raccordements, se référer au manuel séparé. Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende handleiding. INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING FSUN3074-311 [E] NEDERLANDS FRANÇAIS DEUTSCH ENGLISH Thank you for purchasing a JVC product. [. . . ] (The "TP" indicator lights up. ) If a TA programme starts broadcasting while the TA standby mode is active, "TRAFFIC" is displayed and the FM mode is engaged. The volume increases to the preset "TA VOL" level and the TA programme can be heard (see page 14). JAZZ: Jazz music COUNTRY: Country music NATION M: Current popular music from another nation or region, in that country's language OLDIES: Classic pop music FOLK M: Folk music DOCUMENT: Programmes dealing with factual matters, presented in an investigative style 13 ENGLISH PTY codes Descriptions of the PTY Codes Other RDS functions ENGLISH EON (Enhanced Other Networks) · When tuning in a broadcasting station transmitting EON data, the EON indicator is lit and the following operations start. EON automatically stores the frequencies of stations from other networks transmitting information codes (TP/TA/AF/PTY/PS (Programme Service), etc. ) so they can be mutually used. The following points have been improved: When listening to a station NOT transmitting traffic information or the selected PTY for example, EON automatically tunes to a station in a local network when this information is broadcast and then switches back to the original programme when the broadcast ends. (However, it does not switch back to the original programme if the broadcast continues for a long time. ) The transmitted information (AF and other codes) is constantly and automatically updated so that preset programme information can be heard immediately even if in a different network area. Traffic information volume control This function adjusts the volume of traffic information broadcasts. Press the SEL button for more than 2 seconds to set the preferred setting mode. Set to the desired volume with the + or ­ button. (See page 22. ) Number buttons When a number button is pressed, if the station with that frequency is broadcasting a sufficiently strong signal, the receiver will tune to that frequency. When the signal strength is not sufficient for good reception, by referring to the AF list, the receiver searches for a station broadcasting the same programme with a stronger signal. If a station cannot be found in the AF list, PIseek tuning starts. If a station broadcasting the same PI code cannot be detected in one search-cycle, PI-seek tuning is released and the original preset frequency is tuned to. CT (Clock Time) When CT data is received in the RDS signal, the time is correctly renewed. · RDS updates the local time according to Greenwich Mean Time. · When automatic renewal of clock time is NOT required, follow the steps below. Press the SEL button for more than 2 seconds to set the preferred setting mode. Select "AUTO ADJ" with the button. Press the ­ button and set to "ADJ OFF". (See page 22. ) Once these steps are completed, clock time is not renewed even if the CT (Clock Time) data is received with the RDS signal. When you wish to reactivate this mode, repeat the same procedure and in step 3 press the + button to set to "ADJ ON. " In the activated mode, clock time is automatically renewed when the CT data is received. Note: It takes at least 2 minutes to renew the time after receiving CT data. The station must be received for more than 2 minutes continuously, otherwise the clock time will NOT be renewed. [. . . ] All tracks of all discs inserted in the magazine. 26 MAINTENANCE This unit requires very little attention, but you will be able to extend the life of the unit if you follow the instructions below. To clean the heads · Clean the heads after every 10 hours of use using a wet-type head cleaning tape (available at an audio store). When the head becomes dirty, you may realize the following symptoms: ­ Sound quality is reduced. · Do not play dirty or dusty tapes. · Do not touch the highly-polished head with any metallic or magnetic tools. To keep the tape clean · Always store the tapes to their storage cases after use. [. . . ]