User manual JVC KS-FX820

[. . . ] CASSETTE RECEIVER CASSETTEN-RECEIVER RADIOCASSETTE RADIO/CASSETTESPELER KS-FX850R/KS-FX835R/KS-FX820R KS-FX850R /I / ATT 40Wx4 DISP RDS TP 5 MO RND SSM RPT PTY 7 8 9 10 11 12 DOLBY B NR DAB SCM CD-CH FM/AM TAPE KS-FX835R /I / ATT 40Wx4 DISP RDS TP 5 MO RND SSM RPT PTY 7 8 9 10 11 12 DOLBY B NR DAB SCM CD-CH FM/AM TAPE KS-FX820R /I / ATT 40Wx4 DISP RDS TP 5 MO RND SSM RPT PTY 7 8 9 10 11 12 DOLBY B NR DAB SCM CD-CH FM/AM TAPE For installation and connections, refer to the separate manual. Angaben zu Einbau und Verkabelung entnehmen Sie bitte der gesonderten Anleitung. Pour l'installation et les raccordements, se référer au manuel séparé. Zie de afzonderlijke handleiding voor details aangaande het installeren en verbinden van het toestel. INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING FSUN3113-311 [E] NEDERLANDS FRANÇAIS DEUTSCH ENGLISH Thank you for purchasing a JVC product. [. . . ] ­ The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded with no Dolby NR. 19 ENGLISH Finding the beginning of a tune ENGLISH Other convenient tape functions Skipping the blank portions on the tape You can skip blank portions between the tunes. (Blank Skip) When this function is on, the unit skips blank portions of 15 seconds or more, fast-forwards to the next tune, then starts playing it. · See also "Changing the general settings (PSM)" on page 26. Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. SKIP (blank skip)" with ¢ or 4. Select the desired mode with the control dial. The Blank Skip mode alternates between on and off. Note: When the tape reaches its end while fast-forwarding, the tape direction will be changed automatically. Playing the current tune repeatedly You can play the current tune repeatedly. (Repeat Play) RPT Each time you briefly press RPT (Repeat) while playing a tape, Repeat Play turns on and off alternately. Lights up when Repeat Play is turned on. Note: In the following cases, Blank Skip and Repeat Play may not operate correctly: ­ Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions during tunes. ­ Tapes with short non-recorded sections. ­ Tapes with high level noise or humming between tunes. ­ The Dolby NR setting does not match. For example, if Dolby B NR is on and the tape was recorded with no Dolby NR. 20 SOUND ADJUSTMENTS You can adjust the sound characteristics to your preference. 2 CD-CH FM/AM CD 1 Equalization pattern indicator 1 Select the item you want to adjust. BAS VOL Indication BAS (Bass) TRE (Treble) FAD (Fader)* BAL (Balance) To do: Adjust the bass Adjust the treble Adjust the front and rear speaker balance Adjust the left and right speaker balance TRE LOUD FAD BAL Range ­06 (min. ) -- +06 (max. ) ­06 (min. ) -- +06 (max. ) R06 (rear only) -- F06 (front only) L06 (left only) -- R06 (right only) LOUD Boost low and high frequencies to LOUD ON -- LOUD OFF (Loudness) produce a well-balanced sound at low volume level. VOL (Volume) Adjust the volume 00 (min. ) -- 50 (max. ) Note: * If you are using a two-speaker system, set the fader level to "00. " 2 Adjust the level. Equalization pattern changes as you adjust the bass or treble. Note: Normally the control dial works for volume adjustment. So you do not have to select "VOL" to adjust the volume level. 21 ENGLISH Adjusting the sound ENGLISH Using the Sound Control Memory You can select and store a preset sound adjustment suitable to each playback source. (Advanced SCM) Selecting and storing the sound modes Once you select a sound mode, it is stored in memory, and will be recalled every time you select the same source. A sound mode can be stored for each of the following sources -- FM1, FM2, FM3, AM, tape, and external components. · If you do not want to store the sound mode separately for each playback source, but want to use the same sound mode for all the sources, see "Canceling Advanced SCM" on page 28. "Link" indicator CD-CH FM/AM CD SCM SCM Select the sound mode you want. Each time you press the button, the sound mode changes as follows: SCM OFF BEAT SOFT POP · If the "Link" indicator is lit on the display (with "SCM LINK" set to "LINK ON"--see page 28), the selected sound mode can be stored in memory for the current source, and the effect applies to the current source. · If the "Link" indicator is NOT lit on the display (with "SCM LINK" set to "LINK OFF"), the selected sound mode effect applies to any source. Indication SCM OFF BEAT SOFT POP For: Bass (Flat sound) Rock or disco music Quiet background music Light music 00 +02 +01 +04 Preset values Treble 00 00 ­03 +01 Loudness On On Off Off 22 Source buttons CD-CH FM/AM TM£ TAPE Select the source while the "Link" indicator is lit on the display. The "Link" indicator starts flashing, and the sound mode stored in memory for the selected source is recalled. Sound mode indicator Equalization pattern of the selected sound mode appears. LOUD (loudness) indicator Notes: · You can adjust each sound mode to your preference, and store it in memory. [. . . ] · Tighten tapes to remove slack since loose tape may become entangled with the mechanism. · Do not leave a cassette in the cassette compartment after use, as the tape may become slack. The function below is also provided to ensure the longer life of this unit. Ignition key-off Release/Ignition key-on play · When you turn off the ignition key with a cassette in the compartment, the unit automatically releases the tape from its head. · When you turn on the ignition key with a cassette in the compartment, playback automatically starts. 44 TROUBLESHOOTING Symptoms · A cassette tape cannot be inserted. [. . . ]