User manual JVC KSSB200J-KS-SB200 Instruction Manual

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 2 CAUTION--POWER button! Disconnect the mains plug and remove all the batteries to shut the power off completely (all lamps and indications go off). [. . . ] 8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Supplied Accessories · AC power cord · AC adaptor · Antenna If any of these items are missing, contact your dealer immediately. CAUTION: Only use the power cord and AC adaptor provided for this unit to avoid malfunction or damage to the unit. 4 Preparations Connecting the Antenna Do not connect the AC power cord until all other connections have been made. Connect the supplied antenna by referring to the illustration. · Refer also to the manual supplied to the JVC PnP (KTSR2000) for details. For indoor use, place the antenna closer to the window. For outdoor use, place the antenna at a location from obstructions. Antenna cord Antenna cord holder To store the antenna, attach the four holes on the bottom of the antenna into the four projections on top of the unit. Then, slide backward to engage it fully. · You can wind the antenna cord around the antenna cord holder on the rear of the unit. 5 Preparations Mounting JVC PnP Do not connect the AC power cord until all other connections have been made. IMPORTANT: Make sure to turn the power off of both the unit and JVC PnP when attaching/removing JVC PnP. Dock holder 1 2 3 Press PUSH on the top of the unit to open the dock holder. Attach JVC PnP by sliding it down to the dock. · Press in JVC PnP firmly to the dock. Close the dock holder. Note: The internal cooling fan ventilates automatically. Do not close the ventilation slits or the proper ventilation is obstructed. To remove JVC PnP, press PUSH on the top of the unit, then pull out JVC PnP by holding the sides of JVC PnP. Ventilation slits 6 Putting the Batteries into the Unit Battery compartment cover 1 2 3 Push and pull up tabs to open the battery compartment cover on the bottom of the unit to the direction of . Insert 8 batteries by matching the polarity as marked on the compartment. · Insert batteries in order of number as shown in the illustration. Bottom of the unit Tabs · When the power is supplied from AC power with AC adaptor connected to the unit, the batteries are not consumed. CAUTION: To avoid battery leakage or explosion: ­ Remove the batteries when the unit is not in use for an extended period of time. ­ When you need to replace the batteries, replace all 8 batteries at the same time. ­ Do not use different types of batteries together. + ­+ + ­5 +­8 2 3 ­+ ­ ­ 7 + ­ 6+ 4 1 7 Preparations Do not connect the AC power cord until all other connections have been made. Operations Turning on the Power Connecting the AC power cord Connect the unit to the outlet as described in the illustration below. 1 2 Press POWER on the unit. · The sound does not come out when JVC PnP is turned off. 2 AC adaptor Outlet The power-on lamp lights green. · When the power-on lamp lights red, the batteries are almost exhausted. This condition may cause degraded performance. To turn off the power, press POWER on the unit. [. . . ] · Make sure JVC PnP is attached correctly to the dock. Change the position and direction of the antenna. Disconnect headphones. The unit does not operate using batteries. "Antenna Not Detected" appears on the tuner's display. [. . . ]