User manual JVC KS-T807

[. . . ] CASSETTE RECEIVER KS-T807/KS-T707 KS-T807 KS-T707 For installation and connections, refer to the separate manual. . " " () " , , " (7) . , , , / . (), , , , , JVC, , . INSTRUCTIONS GET0212-001A [EE] CCK ENGLISH ENGLISH How to reset your unit After detaching the control panel, press the reset button on the panel holder using a ball-point pen or a similar tool. [. . . ] "MANU" (manual) appears on the display. 4 Press ¢ or 4 repeatedly until the ensemble you want is reached. · If you hold down the button, the frequency keeps changing until you release the button. 5 Press 5 (up) or (down) to select a service (either primary or secondary) you want to listen to. 3 Press and hold ¢ 4 Select a service (either primary or secondary) you want to listen to. To select the next service (If a primary service has some secondary services, they are selected before the next primary service is selected. ) To restore the FM/AM tuner Press and hold FM/AM DAB again. Storing DAB services in memory You can preset up to 6 DAB services in each DAB band (DAB1, DAB2, and DAB3) manually. Press FM/AM DAB briefly if the current source is not "FM/AM" or "DAB". To select the previous service (either primary or secondary) To change the display information while tuning in to an ensemble Normally service name is shown on the display. If you want to check the ensemble name or its frequency, press DISP (display) repeatedly. Each time you press the button, the following information appears for a while on the display. 1 Select the DAB tuner. Each time you press and hold the button, the DAB tuner and the FM/AM tuner are alternately selected. DAB FM/AM Service name Clock Frequency DAB band Ensemble name Channel number 2 Select the DAB band (DAB1, DAB2, or DAB3) you want. Each time you press the button, the DAB band changes as follows: DAB1 DAB2 DAB3 CONTINUED ON THE NEXT PAGE 35 ENGLISH 3 Start searching for an ensemble. To tune in to a particular ensemble without searching ENGLISH 3 Tune in to an ensemble you want. Tuning in to a preset DAB service You can easily tune in to a preset DAB service. Remember that you must store services first. If you have not stored them yet, see "Storing DAB services in memory" on pages 35 and 36. Press FM/AM DAB briefly if the current source is not "FM/AM" or "DAB". 4 Select a service of the ensemble you want to listen to. To select the next service To select the previous service 1 Select the DAB tuner. Each time you press and hold the button, the DAB tuner and the FM/AM tuner are alternately selected. 5 Press and hold the number button (in this example, 1) you want to store the selected service into for more than 2 seconds. DAB FM/AM 2 Select the DAB band (DAB1, DAB2, or DAB3) you want. Each time you press the button, the DAB band changes as follows: DAB1 Selected service name and DAB band/preset number appear alternately for a while. DAB2 DAB3 3 Select the number (1 ­ 6) for the preset DAB service (primary) you want. 6 Repeat the above procedure to store other DAB services into other preset numbers. Notes: · You can only preset primary DAB services. If you store a secondary service, its primary service will be stored instead. · A previously preset DAB service is erased when a new DAB service is stored in the same preset number. · Preset DAB services are erased when the power supply to the memory circuit is interrupted (for example, during battery replacement). If this occurs, preset the DAB services again. Note: If the selected primary service has some secondary services, pressing the same number button repeatedly will tune in to the secondary services. 36 Tracing the same programme automatically (Alternative Reception) You can keep listening to the same programme. · While receiving a DAB service: When driving in an area where a service cannot be received, this unit automatically tunes in to another ensemble or FM RDS station, broadcasting the same programme. · While receiving an FM RDS station: When driving in an area where a DAB service is broadcasting the same programme as the FM RDS station is broadcasting, this unit automatically tunes in to the DAB service. To adjust the DAB volume level You can adjust the volume level of DAB tuner and store it in memory. By adjusting the volume level properly to match it to the FM sound level, you will not need to adjust the volume level each time you change the source. When shipped from the factory, DAB volume level is set at "VOL 00. " · See also "Changing the general settings (PSM)" on page 23. Note: When reception switches between DAB and FM, the listening volume level may increase or decrease inconveniently. This change in the volume level results from unequal audio injection levels at broadcaster site, but not from the malfunction of this unit. To prevent this inconvenience, you can adjust the DAB volume level (see the right column). 1 Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. 2 Press ¢ or 4 to select "DAB VOL" (DAB volume). 3 Turn the control dial to set to the desired volume. [. . . ] (. : K RM-RK60) , : · , . ( ) · ( ). , , , . 1. . ( ) 38 RM-RK60 · / ( ) . · MP3 -, MP3; ­ . [. . . ]