User manual JVC KW-NT30HD

[. . . ] It is dangerous to defeat the safety switches. 5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. About the demonstration mode (DEMO MODE). . . When shipped from the factory, "DEMO" is set to "DEMO ON" in this unit. The demonstration will start automatically if no sound comes in for 3 minutes. (See page 25. ) To deactivate the demonstration mode 1 Press and hold SEL for more than 2 seconds so that one of the PSM items appears on the display. [. . . ] When "EQ LINK" is set to "LINK ON" The selected sound mode and Super Bass level can be stored in memory for the current source. Each time you select the same source, the same sound mode is also recalled, and shown after the source name. When "EQ LINK" is set to "LINK OFF" The selected sound mode effect applies to all the sources selected. 2 Select the sound mode. The sound mode changes as follows: FLAT POP USER** Country Hard Rock JAZZ Raggae R & B* Classic DanceMusic (back to the beginning) * Rhythm and Blues ** If you want to adjust and store your original sound mode (USER), see "Storing your own sound adjustments" on page 20. EQ level changes as you select the sound mode. Ex. : When you select "R & B" To cancel the sound mode, select "FLAT" in step 2. Note: You can adjust the sound mode to your preference, and store it in memory. 19 ENGLISH Selecting preset sound modes To store a sound mode separately for each playback source (EQ Link) ENGLISH Storing your own sound adjustments You can adjust the sound modes to your preference and store your own adjustments in memory (USER sound mode). There is a time limit in doing the following procedure. If the setting is cancelled before you finish, start from step 1 again. 3 Adjust the selected sound element. Refer to the table below for adjusting the selected sound element. Indication Range LOW FREQ. 50 Hz , 80 Hz , 120 Hz LOW LEVEL 06 (min. ) -- +06 (max. ) MID FREQ. 700 Hz , 1 kHz , 2 kHz 06 (min. ) -- +06 (max. ) 1 Select "EQ. " EQ Canceled S. BASS L. V. METER MID LEVEL HIGH FREQ. 8 kHz , 12 kHz HIGH LEVEL 06 (min. ) -- +06 (max. ) EQ level adjusted flashes. 2 Select sound elements to adjust. Each time you press the button, the sound elements to adjust change as follows: EX. : When you adjust "LOW FREQ. " 4 LOW FREQ. * MID FREQ. * HIGH FREQ. * LOW LEVEL MID LEVEL HIGH LEVEL Repeat step 2 and 3 to adjust the other sound elements. 5 Store the adjustments. Your setting is stored in USER sound mode. (back to the beginning) FREQ. (LOW, MID, HIGH): Select the center frequency to adjust. LEVEL (LOW, MID, HIGH): Adjust the enhancement level. If the input level of the connected component is not high enough, increase the input level properly. Without adjusting the line input level, you may be surprised at a loud sound when you change the source from the external component to another source. Adjusting the display contrast level CONTRAST You can adjust the display contrast level among 1 (dark) to 10 (bright). When shipped from the factory, the display contrast level is set at level 5. Selecting the scroll mode SCROLL You can select the scroll mode for the disc information. When shipped from the factory, Auto Scroll mode is set to "SCRL ONCE. " SCRL ONCE: Scrolls only once. SCRL AUTO: Repeats the scroll (5-second intervals in between). SCRL OFF: Cancels Auto Scroll. 24 You can turn the demo mode on or off. When shipped from the factory, "DEMO ON" is selected. The demonstration will start automatically if no sound comes in for 3 minutes. You can assign names to station frequencies and the external component connected to the AUX input jack. After assigning a name, it will appear on the display when you select the source. Sources Station frequencies* Maximum number of the characters Up to 10 characters (up to 32 station frequencies including both FM and AM) Up to 10 characters Note: If the unit has been reset (and the power is on), demonstration will start if no sound comes in for about 15 seconds. External components ("AUX INPUT" only) * You cannot assign name to a station frequency stored in the EX (extra) button. 1 Select a source you want to assign a name to. When you select a source, the power automatically comes on. Each time you press the button, the source changes as described on page 7. 2 Press and hold SEL (select) for more than 2 seconds while pressing DISP (display). (at the same time) CONTINUED TO THE NEXT PAGE 25 ENGLISH Turning the demo mode on or off DEMO MODE Assigning names to the sources ENGLISH 3 Select the character set you want while " " is flashing. Each time you press the button, the character set changes as follows: To erase the input characters Press and hold DISP (display) for more than 1 seconds to erase all the characters at a time. Capital letters ( ) Note: When you try to assign a name to the 33rd station frequency, "NAME FULL" appears on the display. (In this case, delete unwanted names before assignment. ) Small letters ( ) ) Available characters Capital letters A F K P U Z B G L Q V space Numbers and symbols ( C H M R W D I N S X E J O T Y 4 Select a character. About the available characters, see the right column. Small letters 5 Move the cursor to the next (or previous) character position. a f k p u z b g l q v space c h m r w d i n s x e j o t y 6 7 Repeat steps 3 to 5 until you finish inputting the name. [. . . ] BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car. If the speaker wiring in your car is as illustrated in Fig. 2 below, DO NOT connect the unit using that original speaker wiring. If you do, the unit will be seriously damaged. [. . . ]