User manual JVC KW-R900BT

[. . . ] To prevent short circuits, cover the terminals of von 4 bis 8 ). The heat sink becomes very hot after use. Be beträgt, stellen Sie <Amplifier Gain> anders ein, careful not to touch it when removing this unit. um Schäden an den Lautsprechern zu vermeiden · At the time of installation, be sure to fix all wires (siehe Seite 34 der BEDIENUNGSANLEITUNG). [. . . ] (wires both from this unit and from the car itself) · Zur Vermeidung eines Kurzschlusses die in a way that any wires cannot come into contact Anschlußklemmen der NICHT VERWENDETEN with heat sinks on the rear and side of the unit. If any item is missing, consult your JVC IN-CAR ENTERTAINMENT dealer immediately. Crimp connector Crimpanschlüsse Raccord à sertir Krimpaansluiting Flat head screws (M5 × 8 mm) Flachkopfschrauben (M5 × 8 mm) Vis à tête plate (M5 × 8 mm) Schroeven met platte kop (M5 × 8 mm) Round head screws (M5 × 8 mm) Rundkopfschrauben (M5 × 8 mm) Vis à tête ronde (M5 × 8 mm) Schroeven met ronde kop (M5 × 8 mm) Power cord Stromkabel Cordon d'alimentation Stroomkabel Use these screws when installing the unit without the supplied sleeve. The following illustration shows a typical installation. However, you should make adjustments corresponding to your specific car. If you have any questions or require information regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a company supplying kits. If you are not sure how to install this unit correctly, have it installed by a qualified technician. Before installing the unit Be ausgebauten Schrauben und anderen Teile müssen sure to keep all the screws and parts removed zur Wiederverwendung aufbewahrt werden. When mounting the unit, be sure to use the die mitgelieferten Schrauben wie beschrieben screws provided, as instructed. Wenn andere Schrauben used, parts could become loose or damaged. verwendet werden , besteht die Gefahr , dass sich · When tightening screws or bolts, be careful not to Teile lockern oder beschädigt werden könnten. 2 Connect the colored leads of the power cord in the order specified in the illustration below. The terminals and cables of all models are shown in the illustration for the purpose of explanation. To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V) Zur einer stromführenden Anschlußklemme im Sicherungsblock zum Anschließen an die Autobatterie (Umgehen des Zündschalters) (konstant 12 V) A une borne sous tension du porte-fusible connectée à la batterie de la voiture (en dérivant l'interrupteur d'allumage) (12 V constant) Naar een onder spanning staande aansluitklem in het zekeringblok die is aangesloten op de accu van de auto (u passeert de ontstekingsschakelaar) (constant 12 V) To an accessory terminal in the fuse block Zur einer Zubehöranschlußklemme im Sicherungsblock Vers borne accessoire du porte-fusible Naar een aansluitklem in het zekeringblok Fuse block Sicherungsblock Porte-fusible Zekeringblok Only for KW-AVX830: Insert the Bluetooth adapter KS-UBT1 on the front of the unit. Light green Hellgrün Vert clair Lichtgroen Crimp connector Crimpanschlüsse Raccord à sertir Krimpaansluiting Blue with white stripe Blau mit weißem Streifen Bleu avec bande blanche Blauw met witte streep To the remote lead of other equipment or power aerial if any (200 mA max. Installation, this lead must be connected, otherwise power cannot be turned on. Do not connect the lead directly to the battery. If your car is equipped with the steering wheel remote controller, you can operate this unit using the controller. To do it, a JVC's OE remote adapter (not supplied) which matches with your car is required. Connectez le fil de commande à distance (bleu avec bande blanche) au fil de commande à distance de l'autre appareil de façon qu'il puisse être commandé via cet appareil. You can connect an amplifier to upgrade your car stereo system. Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit. [. . . ] Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit. Disconnect the speakers from this unit, and connect them to the amplifier. Leave the speaker leads of this unit unused. You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to get clear sounds and to prevent internal heat built-up inside the unit. [. . . ]