User manual JVC KW-XC777 Instruction Manual

[. . . ] CD/CASSETTE RECEIVER ''/" KW-XC777 EX For installation and connections, refer to the separate manual. հ"`--߷"TMա , "`ߧY'˷" INSTRUCTIONS Yհ", , TM" LVT0834-001A [U] ". . . " ENGLISH ENGLISH 2 IMPORTANT FOR LASER PRODUCTS Precautions: 1. CLASS 1 LASER PRODUCT 2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. There are no user-serviceable parts inside. Leave all servicing to qualified service personnel. 4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches to prevent radiation emission when unloading CDs. [. . . ] You can select any one from 7 different level meter patterns or a demonstration of all the patterns. 1 Select "L. V. METER. " EQ Canceled S. BASS L. V. METER 4. Full Size Level meter is displayed on the main display. 5. Spin Spin in the right meter. 2 Press +/ to select the level meter pattern. Each time you press the button, the level meter changes as follows: 6. Double Waves is displayed on both level meters. ALL DEMO Full Size Dolphin Standard SideWinder Spin Double HIGH WAY OFF (back to the beginning) 7. HIGH WAY As if you were driving along a highway. Level meter patterns 1. ALL DEMO (default setting) Demonstrates all the level meter patterns, each for 20 seconds. 8. Dolphin A dolphin is swimming in the main display. 2. Standard Standard level meter. 9. OFF No level meter is displayed. 21 ENGLISH Selecting level meter patterns 3. SideWinder OTHER MAIN FUNCTIONS ENGLISH Setting the clock After installation, set the built-in clock correctly. Changing general settings (PSM) You can change the following settings for this unit by using the PSM (Preferred Setting Mode) control. 1 Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (See page 23. ) Basic Procedure There is a time limit in doing the following procedure. If the setting is canceled before you finish, start from step 1 again. 1 2 If "CLOCK HOUR" does not appear, press or 4 repeatedly until it appears. Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (See page 23. ) 2 3 Adjust the hour. Select a PSM item you want to adjust. (See page 23. ) 4 Press or 4 until "CLOCK MIN (minute)" appears on the display. 3 Adjust the PSM item selected. 5 Adjust the minute. 4 5 Repeat steps 2 and 3 to adjust the other PSM items if necessary. Finish the setting. 6 Finish the setting. 22 To check the current clock time while the unit is turned off, press DISP (display). The power turns on, the clock time is shown for 5 seconds, then the power turns off. 1 Hold. 2 Select. 3 Factory-preset See Settings page Set. - + Advance Advance CLOCK ON LINK OFF Back Back CLOCK OFF LINK ON CLOCK HOUR Hour adjustment CLOCK MIN Minute adjustment 1:00 CLOCK OFF LINK OFF DIM AUTO 22 24 19 24 24 24 24 24 25 CLOCK DISP Clock display EQ LINK DIMMER CONTRAST SCROLL EXT INPUT AUX ADJ DEMO Sound control memory linkage Dimmer mode Display contrast Scroll mode External input selection Auxiliary input level adjustment Demonstration mode DIM OFF DIM ON DIM AUTO CONTRAST 1 CONTRAST 10 CONTRAST 5 SCRL ONCE SCRL AUTO SCRL OFF CD CHANGER LINE INPUT SCRL ONCE CD CHANGER A. ADJ 00 DEMO ON A. ADJ 00 A. ADJ 05 DEMO OFF DEMO ON 23 ENGLISH Preferred Setting Mode (PSM) items Setting the clock display CLOCK DISP ENGLISH You can set the clock to be shown on the display when the unit is turned off. When shipped from the factory, the clock is set not to be shown on the display. CLOCK OFF: Clock display is turned off. CLOCK ON: Clock display is turned on. Selecting the external component to use EXT INPUT You can connect the external component to the CD changer jack on the rear using the Line Input Adaptor KS-U57 (not supplied). To use the external component as the playback source through this unit, you need to select which component CD changer or external component to use. When shipped from the factory, CD changer is selected as the external component. LINE INPUT: To use the external component other than CD changer. Note: If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select "CLOCK OFF" to save the car's battery. Selecting the dimmer mode DIMMER When you turn on the car headlights, the display automatically dims (Auto Dimmer). When shipped from the factory, Auto Dimmer mode is activated. DIM AUTO: Activates Auto Dimmer. Notes: If the current source is CD changer or external component, this item does not appear. For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/ Connection Manual (separate volume). Note: Auto Dimmer equipped for this unit may not work correctly on some vehicles, particularly on those having a control dial for dimming. In this case, set the dimmer mode to "DIM ON" or "DIM OFF. " Adjusting the auxiliary input level AUX ADJ Adjust the auxiliary input level properly when an external component is connected to the auxiliary input jack. When shipped from the factory, the auxiliary (AUX) input level is set at level 00. If the input level of the connected component is not high enough, increase the input level properly. [. . . ] Redo the speaker wiring so that you can connect the unit to the speakers as illustrated in Fig. If the speaker wiring in your car is as illustrated in Fig. 3, you can connect the unit using the original speaker wiring in your car. If you are not sure of the speaker wiring of your car, consult your car dealer. qO u WOzU dNJë WUDë b e u UNO M U UL ë pí . . . --UO ë W --UD l U UL ë WU b e , , q u U UL K --d{ uB vë oeR lĮ dH pK ë w{-- oeu pK ë q ˫ dLS pK ë Xu XUL . . . --UO ë W--UD `O qJA v U{ dDë lĮ l? [. . . ]