User manual JVC LM-150

[. . . ] LCD DISPLAY MONITOR BEDIENUNGSANLEITUNG: MANUEL D'INSTRUCTIONS: ISTRUZIONI: MANUAL DE INSTRUCCIONES: LCD-DISPLAYMONITOR MONITEUR LCD SCHERMO A CRISTALLI LIQUIDI MONITOR PANTALLA LCD LM-170 LM-150 The illustration of the monitor is of LM-170. Die Abbildung des Monitors zeigt das Modell LM-170. Les illustrations du moniteur sont du LM-170. L'illustrazione del monitor si riferisce al modello LM-170. [. . . ] · The illustrations of the monitor is of LM-170. 7 Using the monitor on the stand You can place the monitor in the following two ways when using the monitor on the supplied stand. You can tilt the monitor upward or downward within the range of about 20° in each direction. When the monitor is attached to the higher position of the stand (see below), you can lift the stand up by 90° and place the monitor as illustrated below. about 20° about 20° NOTE: · Be careful not to pinch your fingers in the gap between the monitor and the stand. · Do not tilt the monitor upward more than 20°; otherwise the monitor may fall over. · When the monitor is attached to the lower position of the stand (see below), you cannot tilt the monitor downward. NOTE: · Be careful not to pinch your fingers in the moving parts. · Make sure to lift the stand up until it stops; otherwise the monitor may fall over. · Place the monitor on a mat to avoid scratching the table surface. · Do not place the monitor in this way when the monitor is attached to the lower position of the stand. To adjust the stand height You can select the stand height--higher position or lower position. · For how to detach the stand, see below. Screw holes for lower position Screw holes for higher position To detach the stand NOTE: · Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel being damaged. Screw (M4 x 10) Stand VESA mounting holes Monitor 11 ENGLISH Installation (cont. ) 7 Installing the monitor on the wall Use a commercial wall mounting unit compliant with the VESA standard (100 mm x 100 mm). NOTE: · Detach the stand first. ( page 11) · Ask your dealer to install. VESA mounting holes (See page 21 for the specifications of the mounting holes. ) 7 Installing the monitor on the rack Use a JVC's RACK MOUNT ADAPTER (RK-C157L1G; not supplied). NOTE: · Detach the stand first. ( page 11) · Ask your dealer to install. 12 How to Use the MAIN MENU Select Adjust When analog RGB signals are input from the computer Select "AUTO ADJ. " Operation guide Shows the buttons for each operation. 7 To exit the menu: Perform "AUTO ADJ. " Select "all reset" Perform "all reset" Next NOTE: · The menu automatically disappears in about 30 seconds after the last menu operation. · Some items may not appear on the menu. Those items are not available for the current input or the current input signal. Cancel 7 MAIN MENU items BACK LIGHT Adjusts the brightness of the display. Setting value: 00 - 25 ASPECT Selects the aspect ratio. Setting value: 4:3, 16:9 NOTE: · Memorized for each input. SHARPNESS Adjusts the clearness of the picture. BAR POSI. Selects the position of the adjustment bars. Setting value: UPPER, LOWER CTI. Adjusts the clearness of the outlines of the color signals (R/G/B). Setting value: OFF, NORMAL, HARD AUTO ADJ. Adjusts the position of the picture automatically when analog RGB signals are input from the computer. By using this function, the picture is displayed as large as possible in the effective screen area. · Adjust the items in "SIZE/POSI. (RGB)" ( page 15) manually when you cannot get a good picture quality with "AUTO ADJ. " LTI. Adjusts the clearness of the outlines of the luminance signal. [. . . ] 17 Use the driver of the graphic board installed into your computer (the driver is supplied with the graphic board). Or, set the monitor to the standard display. · Recommended display setting: 1280 x 1024, 60 Hz (LM-170) 1024 x 768, 60 Hz (LM-150) 16 Installing the driver is required when a computer is connected. -- -- The following are not malfunctions: · When a still image is displayed for a long time, it may remains on the screen after the picture changes. This is due to the characteristics of the LCD display and is not malfunction. [. . . ]