User manual JVC LT-26C31SUE

[. . . ] ENGLISH DEUTSCH FRANÇAIS LT-26C31BUE LT-26C31SUE LT-26C31BJE LT-26C31SJE LCD FLAT TELEVISION LCD-FLACHBILD-FERNSEHER TELEVISEUR A ECRAN PLAT - LCD INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS 1 Warning DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adaptor or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If a new mains plug has to be fitted, then follow the instruction given below: Important Do not make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow. [. . . ] It is recommended to use the AUTO setting if you can. · AUTO cannot be chosen when you are watching the EXT-4 picture. MIN: The level of the DIGITAL VNR effect is set to the minimum. If you set the DIGITAL VNR function to AUTO but feel that the sharpness of the original picture has not been reproduced fully, change the setting from AUTO to MIN. · The MIN setting is not suitable for low-quality pictures which contain a lot of noise. MAX: The level of the DIGITAL VNR effect is set to the maximum. If you set the DIGITAL VNR function to AUTO but still notice some noise, change the setting from AUTO to MAX. · The MAX setting is not suitable for high-quality pictures which contain very little noise. · When a picture of 625p, 525p, or 1125i signal is being displayed, the AUTO setting cannot be chosen with the DIGITAL VNR function. · See "EXT-4 terminal" on page 38 for more information on these types of signals. 19 PICTURE FEATURES COLOUR SYSTEM The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually. Then press the a button The sub-menu of the COLOUR SYSTEM function appears. COLOUR SYSTEM MAIN PAL SUB 4:3 AUTO ASPECT You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Choose 4:3 AUTO ASPECT then press the a button 4:3 AUTO ASPECT PANORAMIC REGULAR 14:9 ZOOM BACK TV OK AUTO D0017-EN BACK TV OK D0016-EN 2 Press the 6 buttons to choose a ZOOM mode. Then press the a button 2 Press the 5 buttons to choose MAIN or SUB MAIN: You can change the colour system of the main-picture. SUB: You can change the colour system of the sub-picture. · Choose MAIN when a sub-picture is not displayed. 3 Press the 6 buttons to choose the appropriate colour system. Then press the a button PAL: PAL system SECAM: SECAM system NTSC 3. 58: NTSC 3. 58 MHz system NTSC 4. 43: NTSC 4. 43 MHz system AUTO: This function detects a colour system from the input signal. You can only use this when you are viewing a picture from programme number PR 0 (AV), or an EXT terminal. · The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually. · When in the programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC 3. 58 or NTSC 4. 43. [. . . ] · The headphone volume is adjusted with the "HEADPHONE" menu. It cannot be adjusted with the r (volume) q buttons. · When TV SPEAKER in the "HEADPHONE" menu is ON, even if the headphones are connected, sound is emitted from the TV speaker. When you do not want to emit sound from the TV speaker, turn the setting OFF. [. . . ]