User manual JVC MX-J150R

[. . . ] COMPACT COMPONENT SYSTEM KOMPAKT-KOMPONENTEN-SYSTEM SYSTEME DE COMPOSANTS COMPACT KOMPACTO KOMPONENTEN-SYSTEEM SISTEMAS DE COMPONENTES COMPACTOS IMPIANTO A COMPONENTI COMPATTO CA-MXJ150R STANDBY OPEN / CLOSE CD1 CD2 CD3 DISC CHANGE COMPACT PLAY & EXCHANGER DIGITAL AUDIO VOLUME COUNTER CLOCK ACTIVE SOUND RESET /TIMER BASS EX. MODE + DEMO DISPLAY MODE PTY /EON ­ SELECT + ­ AUX FM/AM CD TAPE PROGRAM/SET TIMER ON/OFF SLEEP - TUNING TUNING + TAPE A/B CD REC START PHONES REPEAT REC/PAUSE AB DUBBING PROGRAM REPEAT /SET ACTIVE SOUND BASS EX. MODE COMPU PLAY CONTROL ­ PRESET + CD TAPE A/B TUNING MODE FM MODE CD TAPE FM/AM AUX EJECT DISC SKIP EJECT VOL. + FADE MUTING PLAY REC/PLAY VOL. ­ COMPACT FULL-LOGIC CONTROL CD SYNCHRO RECORDING RM­SMXJ100E REMOTE CONTROL DIGITAL AUDIO INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. [. . . ] Before using the timers, you need to set the clock built in the unit. (See page 9. ) 3 Set the on-time you want the unit to turn on. 1) Press 4 or ¢ to set the hour, then press PROGRAM/SET. 2) Press 4 or ¢ to set the minute, then press PROGRAM/ SET. "OFF TIME" appears for 2 seconds, then the unit enters off-time setting mode. Using Daily Timer With Daily Timer, you can wake to your favorite music or radio program. PROGRAM/SET How Daily Timer actually works The unit automatically turns on, set the volume level to the preset level, and starts playing the specified source when the on-time comes. Then, when the off-time comes, the unit automatically turns off (stands by). The timer setting remains in memory until you change it. · There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. · If you have made a mistake while setting timer, press CLOCK/TIMER twice and start from step 1 again. 4 Set the off-time you want the unit to turn off (on standby). 1) Press 4 or ¢ to set the hour, then press PROGRAM/SET. 2) Press 4 or ¢ to set the minute, then press PROGRAM/ SET. The unit enters the volume setting mode. PROGRAM/SET On the unit ONLY: 5 Set the volume level when the unit is turned on. CLOCK /TIMER 1 Press CLOCK/TIMER until " TIMER" appears on the display. The indicator also starts flashing on the display. Press 4 or ¢ to set the volume, then press PROGRAM/SET. The unit enters source selecting mode. · Each time you press the button, the timer setting modes change as follows: Clock time REC CLOCK TIMER PROGRAM/SET 6 Press 4 or ¢ to select the source to play, then press PROGRAM/SET. · Each time you press 4 or ¢, the source changes as follows: FM TAPE MW LW CD 2 Press PROGRAM/SET. "ON TIME" appears for 2 seconds, then the unit enters on-time setting mode. PROGRAM/SET tunes into a specified preset FM station. MW: tunes into a specified preset MW station. LW: tunes into a specified preset LW station. · Make sure there is a CD on the currently selected disc number tray. · Make sure that a tape is in the deck whose deck indicator (A or B) is lit on the display. · Make sure that the tape direction is correct. FM: ­ 18 ­ English Using the Timers Continued English 7 When selecting "FM, " "MW, " or "LW. " Press 4 or ¢ to select the preset station number, then press PROGRAM/SET. The unit enters recording timer setting mode. If you want to continue the Recording Timer setting, go to step 3 of the Recording Timer setting procedure. 3 Press PROGRAM/SET. "ON TIME" appears for 2 seconds, then the unit enters on-time setting mode. PROGRAM/SET PROGRAM/SET 8 Press CLOCK/TIMER. The indicator stops flashing and remains lit. If you have set the Daily Timer with the unit turned on, turn off the unit. CLOCK /TIMER 4 Set the on-time you want the unit to turn on. 1) Press 4 or ¢ to set the hour, then press PROGRAM/ SET. 2) Press 4 or ¢ to set the minute, then press PROGRAM/SET. [. . . ] Nagy energiájú bemeneti jel rendellenes zajt generálhat és a rendszer károsodását okozhatja. Az alább leírt jelek még a maximális megengedett bemeneti szint alatt is a rendszer túlterhelését és a hangszóró tekercsek leégését okozhatják. 2) A magnódeck gyors elretekercselés során keletkez, magas frekvenciájú komponenseket tartalmazó intenzív jelek. 3) Egyéb berendezés be és kikapcsolásakor keletkez kattanó zaj. [. . . ]