User manual JVC MX-J530R

[. . . ] COMPACT COMPONENT SYSTEM KOMPAKTNÍ SYSTÉM MINI WIEA KOMPAKTOWA KOMBINÁLT KOMPAKT RENDSZER CA-MXJ55R/CA-MXJ530R COMPACT DIGITAL AUDIO STANDBY CD3 STANDBY CD3 CD3 CD2 COMPACT CD2 CD3 CD2 COMPACT CD2 CD1 CD1 DIGITAL AUDIO PLAY & EXCHANGER CD1 DIGITAL AUDIO PLAY & EXCHANGER CD1 VOLUME + VOLUME + PHONES PANEL OPEN / CLOSE ­ PHONES PANEL OPEN / CLOSE ­ TAPE SOUND MODE DISPLAY MODE CD COMPU PLAY S. BASS SLEEP COMPU PLAY CONTROL SOUND MODE CONTROL AUX PTY/EON ­ SELECT + FM / AM DISPLAY MODE AUX PTY/EON ­ SELECT + FM / AM TAPE A TAPE A TAPE B TAPE B REC PAUSE REC PAUSE FM MODE FM MODE + PLAY FADE MUTING REC/PLAY FADE MUTING + PLAY REC/PLAY ­ AUTO REVERSE RM­SMXJ55R REMOTE CONTROL ­ AUTO REVERSE RM­SMXJ55R REMOTE CONTROL AUTO REVERSE AUTO REVERSE EJECT EJECT EJECT EJECT CA-MXJ55R CA-MXJ530R INSTRUCTIONS NÁVOD K OBSLUZE INSTRUKCJA OBSLUGI HASZNÁLATI UTASÍTÁSOK For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. [. . . ] · The disc indicator goes off when the unit has detected that there is no CD on the corresponding disc tray. Press 0 corresponding to a CD, not playing or selected currently, to eject and exchange the CD. If you exchange CDs during play, the current play will not stop until all CDs you have exchanged are played. To stop play for a moment Press CD 6. While pausing, the elapsed playing time flashes on the display. To resume play, press CD 6 again. CD ­ 15 ­ Continued To locate a particular point in a track During play, press and hold 1 or ¡. · ¡: Fast forwards the disc. When using the remote control, press and hold 1 / 4 or ¢ / ¡. TUNING · Each time you press the button, CD play mode changes as follows: Program Play Random Play Continuous Play 3 Press one of the disc number PRESET CD3 To go to another track Press 4 or ¢ repeatedly before or during playback. · 4: Goes back to the beginning of the current or previous tracks. · ¢: Skips to the beginning of the next or succeeding tracks. When using the remote control, press 1 / 4 or ¢ / ¡ before playing. buttons (CD 1, CD 2, and CD 3) to select the disc number you want to play. Track number 1 2 CD2 CD1 3 PROGRAM If you press and hold 4 / ¢ (or 1 / 4 or ¢ / ¡ before playing) You can change the tracks continuously. Disc number Program step number 4 Select a track from the CD selected in the above step. On the unit: Press 4 or ¢ to select the track number, then press SET. PRESET To go to another track directly using the number buttons Pressing the number button(s) before or during play allows you to start playing the track number you want. For track number 20, press +10, then 10. For track number 32, press +10, +10, +10, then 2. SEA CONTROL SET On the remote control: Press the number buttons. · For how to use the number buttons, see "To go to another track directly using the number buttons" described to the left. Programming the Playing Order of the Tracks -- Program Play You can arrange the order in which the tracks play before you start playing. · To use Repeat play (see page 17) for Program play, press REPEAT after starting Program play. 1 2 3 PROGRAM 13 5 Program other tracks you want. · To program tracks from the same disc, repeat step 4. · To program tracks from a different disc, repeat steps 3 and 4. 1 Load CDs. · If the current playing source is not the CD player, press CD 6, then 7 before going to the next step. 6 Press CD 6. The tracks are played in the order you have programed. To exit from Program play mode, press PROGRAM/ RANDOM repeatedly again before or after play so that the unit enters another play mode. (The program you have made is stored in memory until you turn off the unit or erase the program. ) 2 Press PROGRAM/RANDOM repeatedly until "PROGRAM" appears on the display. 1 2 3 PROGRAM / RANDOM PROGRAM · If a program has been stored in memory, the program is called up. ­ 16 ­ English English To check the program contents Before playing, you can check the program contents by pressing 1 / 4 or ¢ / ¡ on the remote control. · ¢ / ¡: Shows the programed tracks in the programed order. · 1 / 4: Shows them in the reverse order. To exit from Random play mode, press PROGRAM/ RANDOM repeatedly again before or after play so that the unit enters another play mode. Even if you press 4 (or 1 / 4 on the remote control) You cannot go back to the previous tracks during Random play. · If you press ¢ (or ¢ / ¡ on the remote control), you can go to next random tracks. To modify the program DEMO Before play, you can erase the programed tracks CANCEL shown on the display by pressing CANCEL. · Each time you press the button, the programed track shown on the display is erased from the program. To add tracks in the program before play, simply select the track numbers you want to add by following step 4 of the programming procedure on page 16. To erase the entire program before or after play, press 7. [. . . ] To clean the disc Wipe the disc with a soft cloth in a straight line from center to edge. Handling cassette tapes · If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating. · If the tape is loose, it may get stretched, cut, or caught in the cassette. · Be careful not to touch the tape surface. · Avoid the following places to store the tape: -- In dusty places -- In direct sunlight or heat -- In moist areas -- Near a magnet DO NOT use any solvent -- such as conventional record cleaner, spray, thinner, or benzine -- to clean the disc. ­ 25 ­ ?? ? If you are having a problem with your unit, check this list for a possible solution before calling for service. [. . . ]