User manual JVC MX-J850R

[. . . ] COMPACT COMPONENT SYSTEM CA-MXJ850R STANDBY CD3 COMPACT CD2 DIGITAL AUDIO CD1 PLAY & EXCHANGE VOLUME + PHONES PANEL OPEN / CLOSE ­ TAPE SOUND MODE DISPLAY MODE CD S. A. BASS SLEEP COMPU PLAY CONTROL PTY/EON ­ SELECT + AUX FM / AM COMPACT TAPE A PRO LOGIC 3 STEREO TEST TONE TAPE B ­ CENTER LEVEL + CENTER MODE REC PAUSE ­ REAR LEVEL + DELAY TIME SHIFT L BALANCE R FM MODE DIGITAL AUDIO + FADE MUTING PLAY REC/PLAY ­ RM­SMXJ75R REMOTE CONTROL AUTO REVERSE AUTO REVERSE EJECT EJECT INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. GVT0044-008A [B] Cover. CA-MXJ850R[B]/f 1 00. 4. 21, 4:31 PM Warnings, Cautions and Others IMPORTANT for the U. K. [. . . ] See "How the EON function actually works. " PTY/EON ­ 15 ­ EN10-15. MXJ850R[B]/f 15 00. 4. 21, 4:32 PM Playing Back CDs Loading CDs Playing Back the Entire Discs -- Continuous Play You can play CDs continuously. Continued 1 Press 0 for the disc tray (CD1 to CD3) you want to load a CD onto. The unit automatically turns on and the disc tray comes out. The Powered Rolling Panel also opens automatically. 1 Load CDs. 2 Press one of the disc number buttons (CD1, CD2, and CD3) for the disc you want to play. CD play starts from the first track of the selected disc. CD3 2 Place a disc correctly on the circle of the disc tray, with its label side up. CD2 CD1 Tracks of the currently playing disc CORRECT INCORRECT 1 2 3 · When using a CD single (8 cm), place it on the inner circle of the disc tray. 1 5 9 13 234 678 10 11 12 14 3 Press the same 0 you have pressed in step 1. The disc tray closes, and the corresponding disc number indicator (CD1 to CD3) lights up on the display. Track number Elapsed playing time · Pressing CD £/8 instead of the disc number buttons starts playing back if a CD is on the trays. To remove the disc, press 0 for the corresponding disc tray. 4 Repeat steps 1 to 3 to place other CDs. When loading more than one CD continuously When you press 0 for the next tray you want to place another CD onto, the first disc tray automatically closes and then the next tray comes out. About the disc indicators Each disc indicator corresponds to the disc tray of the same number. Disc number Disc indicator CD playback sequence When 3 CDs are loaded on the disc trays, they are played in one of the following sequences. · When CD1 is pressed : CD1 ] CD2 ] CD3 (then stops) · When CD2 is pressed : CD2 ] CD3 ] CD1 (then stops) · When CD3 is pressed : CD3 ] CD1 ] CD2 (then stops) * When only 2 CDs are loaded, they are played in the same order, but the disc tray without a CD is skipped. 1 2 3 Basic CD Operations While playing a CD, you can do the following operations. To exchange CDs during playback of another Disc marker · The disc marker lights up for the disc number you have selected. · The disc indicator flashes while the corresponding CD is being played. · The disc indicator goes off when the unit has detected that there is no CD on the corresponding disc tray. Press 0 corresponding to a CD, not playing or selected currently, to eject and exchange the CD. If you exchange CDs during play, the current play will not stop until all CDs you have exchanged are played. To stop play for a moment Press CD £/8. While pausing, the elapsed playing time flashes on the display. To resume play, press CD £/8 again. CD ­ 16 ­ EN16-19. MXJ850R[B]/f 16 00. 4. 21, 4:32 PM To locate a particular point in a track During play, press and hold 1 or ¡. · ¡: Fast forwards the disc. When using the remote control, press and hold 1 / 4 or ¢ / ¡. TUNING · Each time you press the button, CD play mode changes as follows: Program Play Random Play Continuous Play 3 Press one of the disc number PRESET CD3 To go to another track Press 4 or ¢ repeatedly before or during playback. · 4: Goes back to the beginning of the current or previous tracks. · ¢: Skips to the beginning of the next or succeeding tracks. When using the remote control, press 1 / 4 or ¢ / ¡ before playing. If you press and hold 4 / ¢ (or 1 / 4 or ¢ / ¡ before playing) You can change the tracks continuously. buttons (CD1, CD2, and CD3) to select the disc number you want to play. Track number 1 2 CD2 CD1 3 PROGRAM Disc number Program step number 4 Select a track from the CD selected in the above step. On the unit: Press 4 or ¢ to select the track number, then press SET. TEST TONE PRESET To go to another track directly using the number buttons PRO LOGIC 3 STEREO Pressing the number button(s) before or during play allows you to start playing ­ CENTER + CENTER MODE LEVEL the track number you want. ­ LEVEL + DELAY TIME For track number 15, press +10, then 5. L BALANCE R For track number 20, press +10, then 10. For track number 32, press +10, +10, +10, then 2. SEA CONTROL SET On the remote control: Press the number buttons. · For how to use the number buttons, see "To go to another track directly using the number buttons" described to the left. PRO LOGIC 3 STEREO TEST TONE ­ CENTER LEVEL + CENTER MODE ­ REAR LEVEL + DELAY TIME L BALANCE R Programming the Playing Order of the Tracks -- Program Play You can arrange the order in which the tracks play before you start playing. · To use Repeat play (see page 18) for Program play, press REPEAT after starting Program play. 1 2 3 PROGRAM 13 5 Program other tracks you want. · To program tracks from the same disc, repeat step 4. · To program tracks from a different disc, repeat steps 3 and 4. 1 Load CDs. · If the current playing source is not the CD player, press CD £/8, then 7 before going to the next step. 6 Press CD £/8. The tracks are played in the order you have programed. [. . . ] ? If you are having a problem with your unit, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person, such as your dealer, for service. Symptom No sound is heard. Hard to listen to broadcasts because of noise. Cause Connections are incorrect or loose. · The AM loop antenna is too close to the unit. [. . . ]