User manual JVC PC-X290

[. . . ] CD PORTABLE COMPONENT SYSTEM PC-X290 Consists of CA-PCX290 and SP-PCX290 SP-PCX290 CA-PCX290 CD PORTABLE COMPONENT SYSTEM STANDBY/ON SP-PCX290 VOLUME + FM MODE SENSOR STANDBY PRE T SE R O T U TAPE IN CD/ RANDOM TUNER/ BAND D I S PL AY P /R E PE AT HBS /PRESET EQ PHONES CD/ RANDOM A M /S ET PR ES A T E DO TAPE TUNER/ BAND AUX WN R PR OG REC PLAY CD SYNCHRO RECORDING AUTO STOP SYSTEM PLAY B REC PLAY REW FF STOP/EJECT PAUSE PLAY REW FF STOP/EJECT PAUSE INSTRUCTIONS LVT1189-001B [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] A little power is always consumed even while the unit is on standby. To switch off the power supply completely, unplug the AC power cord from the AC outlet. If the batteries are inserted in the unit, take them out. When you unplug the AC power cord or if a power failure occurs The clock is reset to "0:00" right away, while the tuner preset stations (see page 12) will be erased in a few days. If the batteries are inserted in the unit, this has no effect on the memory. If there is a power failure The clock loses the setting and is reset to "0:00. " You need to set the clock again. If the batteries are inserted in the unit, this has no effect on the memory. 3 Press 4 or ¢ to adjust the minute, then press PROGRAM/SET. PR E T R O SE T U P/ IN A M /S ET PR ES Setting the Clock Before operating the unit any further, first set the clock built in this unit. · When the unit is turned on with CD or tuner selected, press DISPLAY first to show the clock indication. To show the clock when CD or tuner is selected Press DISPLAY. · Each time you press the button, the display changes the clock indication and the normal indication alternately. (Operating the unit while clock indication is displayed change the display to the normal indication. ) Selecting the Sources To select the FM/AM broadcasts, press TUNER/BAND. (See page 12. ) To select CD, press CD/RANDOM then press 6. (See pages 13 ­ 15. ) To select tapes, press TAPE then press PLAY 3 for the deck you want. (See page 16. ) To select the external equipment as the source, press AUX. The source indicator for the selected source appears on the display. TAPE CD/ RANDOM IN 1 Press and hold PROGRAM/SET for more than 2 seconds. The hour digits start flashing on the display. PR E T R O SE T U A M /S ET PR ES T E DO WN TUNER/ BAND AUX 2 Press 4 or ¢ to adjust the hour, then press PROGRAM/SET. The minute digits start flashing on the display. PR E T R O SE T U IN A M /S ET PR ES T E DO WN ­9­ T E DO WN R RE P E AT PR OG P/ RE P E AT PR OG R P/ RE P E AT PR OG R Adjusting the Volume You can adjust the volume level only while the unit is turned on. Turn the VOLUME +/­ clockwise to increase the volume or counterclockwise to decrease it. · The volume level can be adjusted in 31 steps (00 VOL to 30 VOL). VOLUME Reinforcing the Bass Sound The Hyper Bass Sound function provided for this unit can enhance the bass sound while listening to any source at low volume. · You can use this function only for playback. To turn on the function, press and hold HBS/ PRESET EQ for more than 1 second so that the HBS indicator appears on the display. HBS + HB S/PRESET EQ When using the remote control, press VOLUME + to increase the volume or press VOLUME ­ to decrease it. To turn off the sound temporarily To turn off the function, press and hold the button for more than 1 second again so that the HBS indicator goes off from the display. On the remote control ONLY: Press MUTING. The sounds is turned off and the MUTING indicator appears on the display. To restore the sound, press MUTING again. · Adjusting the volume level also cancels the muting. Selecting the Sound Modes You can select one of the 5 preset sound modes. SEA (Sound Effect Amplifier) modes: CLASSIC: Good for classical music. · This function only affects the playback sound, but does not affect your recording. [. . . ] To stop during dubbing, press STOP/EJECT 7/0 for the deck A. To stop recording for a moment, press PAUSE 8. The recording is paused, but the CD playback does not stop. To resume recording, press PAUSE 8 again. To stop recording, press STOP/EJECT 7/0. [. . . ]