User manual JVC RD-1555 service manual

[. . . ] DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nontheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. [. . . ] I Set the preset number by pressing and holding the number key on the Remote Control until "STORED" appears on the display. To preset numbers 1 to 10: Press the number key and hold it down for 2 seconds. To preset numbers 11 to 19: Press the +10 button, then press the second number key (1 to 9) and hold it down for 2 seconds. To preset numbers 21 to 29: Press the +10 button twice, then press the second number key (1 to 9) and hold it down for 2 seconds. To preset number 30: Press the +10 button twice, then press and hold 10 button. I Repeat steps 1-2 for the other band. I If you want to change any of the auto preset stations, follow the procedure for Manual Presetting. CAUTION: To prevent the preset stations from being erased because of a power failure, etc. , install memory backup batteries in the System. (See page 2. ) Otherwise, they will be erased in approx. half a day. Manual Presetting (Using the Unit) -- (Station Select) MULTI CONTROL TUNER BAND AUTO PRESET MANUAL/ PRESET TUNING MANUAL/ PRESET TUNING (Preset No. Select) (for 2 sec) MANUAL/ PRESET TUNING 5. I Repeat steps 2 - 4 for further presetting. MANUAL/ PRESET TUNING MULTI CONTROL MANUAL/ PRESET TUNING (Press & hold ) To change the preset stations, repeat the same steps as above. To Change the FM Reception Mode The "STEREO" indicator lights up and you can hear stereo effects, when a program is broadcast in stereo. However if an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose any stereo effect. 1. I Select a band by pressing the TUNER BAND button. The CD Player automatically stops when the last track of the CD has finished playing. During playback, the track number being played and the playback time elapsed are shown on the display. Track number Playback time elapsed Normal Play 1. I Press the 0 button on the Unit. The CD cover (including the display) opens. To stop playing the CD, press the 7 button. The following information for the CD is displayed. Total number of tracks 2. I Place a CD, with its label side up. Total playback time To pause, press the CD 38. Play continues from the point where it was paused. Notes: You can place an 8 cm (3'') CD without an adaptor. If the CD cannot be read correctly (because it is scratched, for example), "0 0:00" appears on the display. 3. I Press the 0 button again to close the CD cover. To close the CD cover and directly start playback, omit this step and go to the next step. Skip Play (4 or ) ---------------- During playback, press the 4 or button to select the track you want. Press the button to go forward one track at a time. Press the 4 button to go back to the beginning of the current track. [. . . ] (When the source is CD or TUNER, pressing any button on the Unit cancels the timer. ) 11 I Care And Maintenance I Handle your CDs carefully, and they will last a long time. Compact Discs Only CDs bearing these marks can be played with this Unit. Recordable ReWritable Continued use of irregularly shaped CDs (heart-shape, octagonal, etc. ) can damage the Unit. Remove the CD from its case by holding it at the edges while pressing the case's center hole lightly. Do not touch the shiny surface of the CD, or bend the CD. Put the CD back in its case after use to prevent warping. Be careful not to scratch the surface of the CD when placing it back in the case. [. . . ]