User manual JVC RD-T70R

[. . . ] CD PORTABLE SYSTEM RD-T70RBU RD-T50RLB SNOOZE /DIMMER SLEEP STANDBY/ON 1 4 7 10 TUNER BAND 2 5 8 +10 3 6 9 REPEAT CD FM MODE BASS/TREBLE AHB PRO VOLUME REMOTE CONTROL RM-SRDT7A [RD-T70RBU Only] INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0931-005A [B] Warnings, Cautions and Others IMPORTANT FOR LASER PRODUCTS REPRODUCTION OF LABELS 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE IMPORTANT for the U. K. [. . . ] However if an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose any stereo effect. 1. I Select a band by pressing the TUNER BAND button. I Press the 7 button until "MANUAL (Manual Tuning mode)" appears on the display. I Press the 4 or button to tune in a sta4. I Press the 7 button for 2 seconds or more. The preset number and band/frequency are alternately displayed for 5 seconds. Press the TUNER BAND button to select FM MONO mode. The "MONO" indicator lights up on the display. To restore the stereo effect, press the TUNER BAND button to select FM Auto mode. The "MONO" indicator goes out. 5. I Within 5 seconds, repeatedly press the 4 or button until the preset number you want appears, then press and hold the 7 button until "STORED" appears on the display. 6. I Repeat steps 2-5 for further presetting. To change the preset stations, repeat the same procedure as above. 6 Receiving FM Stations with RDS You can use the RDS (Radio Data System) by using the CLOCK/ DISPLAY button on the Unit. RDS allows FM stations to send additional signals with their regular program signals. For example, the stations send their station names, and information about what type of program they broadcast, such as sports or music, etc. However, this unit can only receive the following type of RDS signal: PS (Program Service): shows commonly known station names. PS (Program Service): While searching, "WAIT PS" and "PS" alternately appear on the display. Then, the RDS indicator lights up and the station name appears. "NO PS" appears if no signal is sent. Clock: Current time appears on the display. Station Frequency: Station frequency (non-RDS service) Notes: If searching finishes at once, "WAIT PS" and "PS" will not appear on the display. RDS is not available for AM (MW) broadcasts. On characters displayed When the display shows PS signals: The display shows upper case letters only. The display cannot show accented letters; For example, "A" may represent accented "A's" like ", , , , and ". To show the RDS signals on the display ------------------------------ Press the CLOCK/DISPLAY button on the Unit while listening to an FM station. Each time you press the button, the display changes to show information in the following order: CLOCK/ DISPLAY PS Clock Frequency [Example of characters displayed] ! 7 I Using the CD Player I SNOOZE /DIMMER SLEEP STANDBY/ON CD cover (including the display) 1 4 7 10 TUNER BAND 2 5 8 +10 3 MULTIJOG 6 9 REPEAT VOLUME Number keys STANDBY/ON CLOCK/ DISPLAY SLEEP CD PORTABLE SYSTEM RD-T70R AHB PRO RANDOM/ REPEAT BASS/ TREBLE Jog dial REPEAT STANDBY CD FAVORITE TIMER TIMER1 TIMER2 FM MODE CD 38 AHB PRO MULTI CONTROL MANUAL/ PRESET TUNING SNOOZE DIMMER CD TUNER BAND AUTO PRESET BASS/TREBLE VOLUME 7 4 Track number 7 4 CD 38 0 (CD OPEN/CLOSE) Playing time, Preset number REMOTE CONTROL RM-SRDT7A [RD-T70RBU only] Random/Repeat indicator (Display when using the CD Player) You can use Normal, Random, or Repeat Play. Repeat Play can be set to repeat all or just one of the tracks on the CD. 4. [. . . ] Avoid exposure to direct sunlight, temperature extremes, and moisture. If a CD is dirty, wipe it with a soft cloth in a straight line from center to edge. CAUTION: Do not use any solvent (for example, conventional record cleaner, spray thinner, benzine, etc. ) to clean a CD. Moisture Condensation Moisture may condense on the lens inside the Unit in the following cases: After turning on heating in the room. If the Unit is brought directly from a cold to a warm place. Should this occur, the Unit may malfunction. [. . . ]