User manual JVC RX-1001VBK parts list

[. . . ] ATTENTION Des changements ou modifications non approuvés par JVC pourront invalider l'autorité de l'utilisateur à opérer cet appareil. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. For U. S. A This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] · If you have used Quick Speaker Setup on page 20, this setting is not required. On the front panel ONLY: Before you start, remember. . . There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. Ex. : When setting DIGITAL IN 1 terminal. Setting subwoofer information--SUBWOOFER Select whether you have connected a subwoofer or not. SUBWFR <YES> Select when you have connected a subwoofer. The subwoofer indicator ( S. WFR ) lights up on the display. You can adjust the subwoofer output level (see page 27). Select when you have disconnected a subwoofer. Selecting this changes the front speaker size to "LRG" (see below). 1 Press SETTING. MULTI JOG now works for the setting operation. SUBWFR <NO> 2 Turn MULTI JOG until the item you want to set appears on the display. · As you turn MULTI JOG, the setting items change as follows: ANALOG L S. WFR R Initial setting: SUBWFR <NO> Setting the speaker size--FRONT SPK (front speakers), CENTER SPK (center speaker), SURROUND SPK (surround speakers), S BACK SPK (surround back speakers) Register the sizes of all the connected speakers. QUICK SPK SET FRONT SPK SURROUND SPK S BACK OUT FRONT L DIST CENTER DIST SURR R DIST S BACK L DIST EX/ES/PLIIx SUBWOOFER OUT LFE ATT DIGITAL IN 1 DIGITAL IN 3 VCR VIDEO IN (Back to the beginning) SUBWOOFER CENTER SPK S BACK SPK DIST UNIT FRONT R DIST SURR L DIST S BACK DIST S BACK R DIST DUAL MONO CROSSOVER MIDNIGHT MODE DIGITAL IN 2 DVD VIDEO IN DBS VIDEO IN <LRG> (large) <SML> (small) <NO> Initial setting: Select when the cone speaker size is larger than 12 cm (4 3/4 inches). Select when the cone speaker size is smaller than 12 cm (4 3/4 inches). Select when you have disconnected a speaker. D MONO <MAIN> Select to play back the main channel (Ch 1). * Signal indicator "L" lights up while playing back this channel. D MONO <SUB> Select to play back the sub-channel (Ch 2). * Signal indicator "R" lights up while playing back this channel. D MONO <ALL> Select to play back both the main and subchannels (Ch 1/Ch 2). * Signal indicators "L" and "R" light up while playing back these channels. Initial setting: D MONO <MAIN> * Dual Mono signals can be heard from the following speakers--L (left front speaker), R (right front speaker), and C (center speaker), with respect to the current Surround setting: With Surround Activated Dual Mono setting Without Surround L MAIN SUB ALL NOTE The Dual Mono format is not identical with bilingual broadcasting for TV programs. So this setting does not take effect while watching such bilingual programs. Ch 1 Ch 2 Ch 1 R Ch 1 Ch 2 Ch 2 L Center speaker setting SML/LRG C Ch 1 Ch 2 Ch 1+Ch 2 R L Ch 1 Ch 2 NO R Ch1 Ch 2 Setting the crossover frequency--CROSSOVER Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned to the small speaker to the large speakers. To use this function properly, set this crossover frequency level according to the size of the small speaker connected. · If you have selected "LRG (large)" for all speakers (see page 22), this function will not take effect ("CROSS OFF" appears). CROSS <80Hz> Select when the cone speaker unit built in the speaker is about 12 cm (4 3/4 inches). CROSS <100Hz> Select when the cone speaker unit built in the speaker is about 10 cm (3 15/16 inches). [. . . ] Check speaker wiring, then reconnect if necessary (see page 6) after unplugging the power cord. Check the audio connections (see pages 7 to 11) after unplugging the power cord. Press MUTING to cancel the mute (see page 14). Select the correct input mode (analog or digital). [. . . ]