User manual JVC RX-5042S

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-5042S TA/NEWS/INFO DISPLAY MODE INSTRUCTIONS LVT1140-010A [B] Warnings, Cautions, and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] Therefore, it makes the unit work in the same way as the "ALARM" signal does. TA NEWS INFO TA/NEWS TA/INFO Canceled TA/NEWS/INFO NEWS/INFO TA: Traffic Announcement in your area. INFO: Program the purpose of which is to impart advice in the widest sense. Notes: Enhanced Other Networks data sent from some stations may not be compatible with this receiver. In Enhanced Other Networks standby mode, if you carry out synchronized recording (see page 31), Enhanced Other Networks standby mode is canceled temporarily. The receiver goes back to Enhanced Other Networks standby mode again when the recording is finished. While listening to a program tuned in by the Enhanced Other Networks function, you can only use the DISPLAY MODE and TA/NEWS/INFO buttons as the tuner operation buttons. While listening to a program tuned in by the Enhanced Other Networks function, you cannot change to another source or station. To change it, press TA/NEWS/INFO button first to cancel Enhanced Other Networks. When the current source is "FM" CASE 1 If the station currently tuned in starts broadcasting the program you have selected The receiver continues to receive the station, but the indicator of received program type starts flashing. ` When the program is over, the indicator of received program type stops flashing and remains lit, but the receiver remains in Enhanced Other Networks standby mode. CASE 2 If another FM station starts broadcasting the program you have selected while you are listening to an FM station CAUTION: When the source alternates intermittently between the station tuned in by the Enhanced Other Networks function and the currently selected source, press TA/NEWS/INFO repeatedly to cancel the Enhanced Other Networks function. If you do not press the button, the currently tuned station is received finally, and one of the TA/NEWS/INFO indicators flashing on the display disappears. The receiver automatically switches to the station. The indicator of received program type starts flashing. ` When the program is over, the receiver goes back to the station previously tuned in, but still remains in Enhanced Other Networks standby mode. The indicator of received program type stops flashing and remains lit. 18 Basic Settings Some of the following settings are required after connecting and positioning your speakers while others will make operations easier. You can use QUICK SPEAKER SETUP to easily set up your speaker configuration. Quick Speaker Setup Remote NOT 5 Press in MULTI JOG (PUSH SET). "COMPLETE" appears on the display, then goes back to the source indication. Quick Speaker Setup helps you to easily and quickly register the speaker size and speaker distance according to your listening room to create the best possible surround effect. You can also register each speaker's information manually. For details, see page 21. Notes: This procedure will not be completed if you stop in the middle of the setting process. Once Quick Speaker Setup is performed, the speaker output levels are also set to appropriate values automatically (common to all sources). If you want to set the speaker output levels separately for each source, see "Adjusting the Speaker Output Levels" on page 25. Before you start, remember. . . There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. Speaker channel number and the size You can find how each of the speaker size is defined according to the number of connected speakers (speaker channel "CH" number) you select. Subwoofer (S. WFR) is counted as 0. 1 channel. The size of the connected speakers CH 2. 0CH 2. 1CH 3. 0CH 3. 1CH 4. 0CH 4. 1CH 5. 0CH 5. 1CH L/R LARGE SMALL LARGE SMALL LARGE SMALL LARGE SMALL C NONE NONE SMALL SMALL NONE NONE SMALL SMALL LS/RS NONE NONE NONE NONE SMALL SMALL SMALL SMALL S. WFR NO YES NO YES NO YES NO YES 1 Press QUICK SPEAKER SETUP. "SPK=" and the initial speaker channel number (5. 0CH) appear. 2 Turn MULTI JOG to select an appropriate number of the connected speakers (speaker channel number). As you turn the jog, the speaker channel number changes as follows. For the details of speaker channel number, see "Speaker channel number and the size. " 5. 0CH " 5. 1CH " 2. 0CH " 2. 1CH " 3. 0CH " 3. 1CH " 4. 0CH " 4. 1CH " (Back to the beginning) Room size and the speaker distance According to the selected room size, speaker distance for each activated speaker is set as follows: Size L Speaker L/R C LS/RS Distance 3. 0 m (10 ft) 3. 0 m (10 ft) 3. 0 m (10 ft) 2. 7 m (9 ft) 2. 4 m (8 ft) 2. 1 m (7 ft) 2. 4 m (8 ft) 2. 1 m (7 ft) 1. 5 m (5 ft) 3 Press in MULTI JOG (PUSH SET). "ROOM SIZE=" and the initial room size setting appear. (Large) 4 Turn MULTI JOG to select an appropriate room size to match to your listening room. As you turn the jog, the room size changes as follows. To select your appropriate room size, see "Room size and the speaker distance. " M (Medium) L/R C LS/RS S (Small) L/R C LS/RS Note: L (Large) S (Small) M (Medium) In the tables above, "L" stands for the left front speaker, "R" for the right front speaker, "C" for the center speaker, "LS" for the left surround speaker, "RS" for the right surround speaker, and "S. WFR" for the subwoofer. 19 Basic Settings Basic Setting Items On the following pages, you can adjust the following items: You can only select the items currently available. For details, see the explanation of each item. [. . . ] Press STANDBY/ON on the front panel to turn off the receiver. Turn on the receiver again, and adjust the volume. on the front panel to turn Press STANDBY/ON off the receiver, then check the speaker wiring. If "OVERLOAD" does not disappear, unplug the AC power cord, then plug it back again. [. . . ]