User manual JVC RX-5052SB

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-5052S TA/NEWS/INFO DISPLAY MODE INSTRUCTIONS LVT1290-003A [B] Warnings, Cautions, and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] When the last received FM station is a non-RDS station. The Enhanced Other Networks function is only applicable to preset FM stations. You can use the Enhanced Other Networks function while listening to any source. However, to use the RDS operation buttons on remote control, the remote control operation mode must be set for the tuner operations mode (see page 31). Press TA/NEWS/INFO repeatedly to select the program type(s) you want. Each time you press the button, the program type(s) change, and the corresponding indicators light up on the display. When the current source is other than "FM" CASE 3 If a station starts broadcasting the program you have selected while listening to any source other than "FM" When a station is or starts broadcasting the program you have selected, the receiver automatically switches to the station. The indicator of received program type starts flashing. ` When the program is over, the receiver goes back to the previously selected source, but still remains in Enhanced Other Networks standby mode. The indicator of received program type stops flashing and remains lit. To stop listening to the program selected by the Enhanced Other Networks function Press TA/NEWS/INFO so that the program type (TA/NEWS/INFO) indicator stops flashing and remains lit. The unit enters the Enhanced Other Networks standby mode and goes back to the previously selected source. If an "ALARM" (or TEST) signal is received from a station, the receiver automatically tunes in to the station. While receiving an emergency broadcast, "ALARM" appears on the display. The TEST signal is used for testing the "ALARM" signal. Therefore, it makes the unit work in the same way as the "ALARM" signal does. TA NEWS INFO TA/NEWS TA/INFO Canceled TA: INFO: TA/NEWS/INFO NEWS/INFO Traffic Announcement in your area. Program the purpose of which is to impart advice in the widest sense. NEWS: News. Notes: Enhanced Other Networks data sent from some stations may not be compatible with this receiver. While listening to a program tuned in by the Enhanced Other Networks function, you can only use the DISPLAY MODE and TA/NEWS/INFO buttons as the tuner operation buttons. While listening to a program tuned in by the Enhanced Other Networks function, you cannot change to another source or station. To change it, press TA/NEWS/INFO button first to cancel Enhanced Other Networks. When the current source is "FM" CASE 1 If the station currently tuned in starts broadcasting the program you have selected The receiver continues to receive the station, but the indicator of received program type starts flashing. ` When the program is over, the indicator of received program type stops flashing and remains lit, but the receiver remains in Enhanced Other Networks standby mode. CASE 2 If another FM station starts broadcasting the program you have selected while you are listening to an FM station CAUTION: When the source alternates intermittently between the station tuned in by the Enhanced Other Networks function and the currently selected source, press TA/NEWS/INFO repeatedly to cancel the Enhanced Other Networks function. If you do not press the button, the currently tuned station is received finally, and one of the TA/NEWS/INFO indicators flashing on the display disappears. The receiver automatically switches to the station. The indicator of received program type starts flashing. ` When the program is over, the receiver goes back to the station previously tuned in, but still remains in Enhanced Other Networks standby mode. The indicator of received program type stops flashing and remains lit. 18 Basic Settings Some of the following settings are required after connecting and positioning your speakers while others will make operations easier. [. . . ] (See pages 4 and 5. ) Move the antenna farther from automobile traffic. Press STANDBY/ON on the front panel to turn off the receiver. Turn on the receiver again, and adjust the volume. Press STANDBY/ON on the front panel to turn off the receiver, then check the speaker wiring. [. . . ]