User manual JVC RX-517VTN

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. [. . . ] Set the distance from your listening point to the speakers. By referring to the speaker distance setting, this unit automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you with the same timing. If you have used Quick Speaker Setup on page 16, this setting is not required. Measuring unit--DISTANCE UNIT Select which measuring unit you use. UNIT METER: Select to set the distance in meters. UNIT FEET: Select to set the distance in feet. SWFR LFE+MAIN: Select to emit the bass elements of the front speakers' channels (MAIN) adding to the effect of "SWFR LFE" when no bass elements are emitted through the subwoofer. Notes: When "SUBWOOFER" is set to "SUBWOOFER NO" (see the left column), this function is not available. * The LFE signals are emitted only when playing the following software with the LFE signals: Dolby Digital multi channel software DTS multi channel software When playing an analogue source or a linear PCM software, no LFE signals are emitted. 18 Crossover frequency--CROSSOVER You can select the crossover frequency for the small speakers used. The signals below the preset frequency level will be sent to and be reproduced by the subwoofer (or by "LARGE" speakers when "SUBWOOFER" is set to "SUBWOOFER NO"). Select one of the crossover frequency levels according to the size of the small speaker connected. CROSS 80HZ: Select when the cone speaker unit built in the speaker is about 12 cm. Selecting the Main or Sub Channel You can select the playback sound (channel) you want while playing digital software recorded (or broadcast) in Dual Mono mode (see page 24), which includes two monaural channels separately. Dual Mono--DUAL MONO Select the playback sounds (channel). This function does not work when activating the DSP mode (see page 27). 20 Adjusting Sound You can make sound adjustment to your preference after completing basic settings. Basic Adjustment Items On the following pages, you can adjust the following items: You can adjust only the items applicable to the current sound mode. Items DEQ 63HZ DEQ250HZ DEQ 1KHZ DEQ 4KHZ DEQ16KHZ FRONT L LEVEL To do Adjust equalizer pattern at 63 Hz. Adjust the left front speaker output level. See page 22 22 22 22 22 22 22 22 22 22 22 22 22 22 Basic Procedure Remote NOT Before you start, remember. . . There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. When adjusting the subwoofer level to "3. " SUBWFR LEVEL Adjust the subwoofer output level. 1 Press ADJUST. The last selected item appears on the display. FRONT R LEVEL Adjust the right front speaker output level. CENTER LEVEL Adjust the center speaker output level. SURR L LEVEL SURR R LEVEL EFFECT*1 CENTER TONE 2 Adjust the left surround speaker output level. Adjust the right surround speaker output level. Make the center tone soft or sharp. 2 Turn MULTI JOG until an item you want appears on the display. In this example, select "SUBWFR LEVEL. " For available items, see the list "Basic Adjustment Items. " PANORAMA CTRL* Add "wraparound" sound effect with side-wall image. 3 Press in MULTI JOG (PUSH SET). Notes: * Adjustable when one of the DAP modes or Mono Film (see pages 26 and 27) is in use. [. . . ] (See page 11. ) Select the correct source. (See page 13. ) Select the correct input mode (analog or digital). (See pages 11 and 12. ) If subwoofer is connected, set "SUBWOOFER YES" so that the SUBWOOFER OUT ON/OFF button works. Connect an outdoor FM antenna or contact your dealer. [. . . ]