User manual JVC RX-7010R

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-7010RBK / RX-7012RSL CATV/DBS DVD TV/DBS VCR DVD MUILTI VCR TV CD TAPE/CDR AUDIO FM/AM PHONO - BASS + DSP MODE - TREBLE + SURROUND ON/OFF ANALOG/DIGITAL SLEEP INPUT BASS BOOST EFFECT + CENTER 1 TEST 2 MENU 3 6 ENTER + REARL 4 SOUND 5 8 0 FM MODE REARR + AUDIO/VIDEO CONTROL RECEIVER 7/P MUTING 9 FM/AM TUNING FM/AM PRESET FM MODE EON PTY SEARCH TA/NEWS/INFO DISPLAY MODE SUB WOOFER + 10 RETURN CA TV/DBS CONTROL +10 100+ COMPULINK Remote STANDBY MEMORY MASTER VOLUME + CH + TV VOL + VOLUME STANDBY/ON DIGITAL SURROUND DIGITAL TV/VIDEO - - - + TUNING PLAY /REW PAUSE FF/ SURROUND ON/OFF INPUT ANALOG/DIGITAL BASS BOOST ADJUST SETTING DVD MULTI INPUT ATT DVD VCR TV SOUND/DBS - SOURCE NAME DSP MODE SPEAKERS ON/OFF 1 2 CONTROL DOWN UP REC PAUSE PTY PTY SEARCH PTY+ PHONO CD TAPE/CDR FM/AM DIGITAL SOURCE NAME STOP CONTROL DISPLAY PHONES RM-SRX7010R A/V CONTROL RECEIVER INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0579-005A [B] Warnings, Cautions and Others IMPORTANT for the U. K. [. . . ] For channel number 30, press +10, +10, then 10. EFFECT CENTER + 1 TEST 2 MENU 3 6 ENTER REAR L + 4 7/P 10 RETURN 5 8 0 FM MODE REAR R + 9 SPK 1 ANALOG L R SUB WOOFER + +10 100+ TUNED Note: When you use the 10 keys on the remote control, be sure that they are activated for the tuner, not for the CD and others. (See page 32. ) AUTO: When a program is broadcasted in stereo, you will hear stereo sound; when in monaural, you will hear monaural sounds. This mode is also useful to suppress static noise between stations. The AUTO MUTING indicator lights up on the display. MONO: Reception will be improved although you will lose the stereo effect. In this mode, you will hear noise while tuning into the stations. The AUTO MUTING indicator goes off from the display. Note: When using the FM MODE button on the remote control, be sure that the 10 keys are activated for the tuner, not for the CD and others. (See page 32. ) 19 Using the RDS (Radio Data System) to Receive FM Stations RDS allows FM stations to send an additional signal along with their regular program signals. For example, the stations send their station names, as well as information about what type of program they broadcast, such as sports or music, etc. When tuned to an FM station which provides the RDS service, the RDS indicator lights up on the display. With the receiver, you can receive the following types of RDS signals. PS (Program Service): Shows commonly known station names PTY (Program Type): Shows types of broadcast programs RT (Radio Text): Shows text messages the station sends EON (Enhanced Other Network): See page 21. Notes: When pressing DISPLAY on the remote control, make sure that you have selected FM station using the remote control. If not, the DISPLAY button does not work for tuner operation. (Pressing FM/ AM activates the remote control for tuner operation. ) If searching finishes at once, "PS, " "PTY, " and "RT" will not appear on the display. Searching for a Program by PTY Codes One of the advantages of the RDS service is that you can locate a particular kind of program from the preset channels (see page 18) by specifying the PTY codes. To search for a program using the PTY codes Before you start, remember. . . The PTY Search is only applicable to preset stations. To stop searching any time during the process, press PTY SEARCH while searching. There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. When pressing the buttons on the remote control, make sure that you have selected the FM station using the remote control. If not, the RDS operation buttons do not work for RDS operation. (Pressing FM/AM activates the remote control for RDS operation. ) Notes: RDS is not available for AM (MW/LW) broadcasts. RDS may not operate correctly if the station tuned is not transmitting RDS signal properly or if the signal strength is weak. What information can RDS signals provide? You can see the RDS signals the station sends on the display. [. . . ] Press STANDBY/ON on the front panel to turn off the receiver. After unplugging the power cord, consult your dealer. Select the correct remote control operation mode. (See page 32). Sound from one speaker only. Speaker signal cables are not connected properly. [. . . ]