User manual JVC RX-730R

[. . . ] AUDIO/VIDEO CONTROL RECEIVER AUDIO/VIDEO-RECEIVER MIT STEUEREINHEIT AMPLI/TUNER DE COMMANDE AUDIO/VIDEO GEINTEGREERDE AUDIO/VIDEO-VERSTERKER RECEPTOR DE CONTROL DE AUDIO/VDEO RICEVITORE DI CONTROLLO AUDIO/VIDEO RX-730RBK SEND/LEARN ERROR TV VCR AUDIO SEQUENTIAL PROGRAM KEY SLEEP A ONE TOUCH OPERATION B C SOURCE SELECT VIDEO 1 VIDEO 2 VCR SURROUND MODE TV SOUND FM AM SEA MODE TAPE CD PHONO RX-730R AUDIO/VIDEO CONTROL RECEIVER MASTER VOLUME VIDEO1 VIDEO2 VCR TV SOUND FM AM CD PHONO TAPE MENU ONE TOUCH OPERATION MENU EXIT + SOURCE MUTE SURROUND MODE SEA MODE ON SCREEN CONTROL SURROUND ADJUST SEA ADJUST MEMORY L BALANCE R VOLUME SETTING TUNER MEMORY VIDEO 2 STANDBY POWER DISPLAY MODE TA/NEWS/INFO EON PTY SEARCH VIDEO L AUDIO R SPEAKERS 1 2 PHONES STANDBY/ON RM-SR730RU REMOTE CONTROL _ON --OFF _ON --OFF INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LET0054-001A [EF, G] Warnings, Cautions and Others/Warnung, Achtung und sonstige Hinweise/ Mises en garde, prcautions et indications diverses/Waarschuwingen, voorzorgen en andere mededelingen/Avisos, precauciones y otras notas/ Avvertenze e precauzioni da osservare IMPORTANT for the U. K. [. . . ] Each time you press the button, the display changes to show you the following information: PS Front panel PTY RT Frequency PS (Program Service): While searching, "PS" appears and then the station names will be displayed. "NO PS" appears if no signal is sent. PTY (Program Type): While searching, "PTY" appears and then the type of the broadcast program will be displayed. "NO PTY" appears if no signal is sent. RT (Radio Text): While searching, "RT" appears and then text messages the station sends will be displayed. "NO RT" appears if no signal is sent. Station Frequency: Station frequency (non-RDS service) Page 23 TUNER \ Remote: Inside Notes: If searching finishes at once, "PS", "PTY", and "RT" will not appear on the display. If you press DISPLAY MODE while listening to an AM (MW/LW) station, the display only shows station frequency. RDS is not available for AM (MW/LW) broadcasts. See also page 39. Searching for a Program by PTY Codes MENU One of the advantages of the RDS service is that you can locate a particular kind of program from the preset channels by specifying the PTY codes. To search for a program using the PTY codes On the front panel: 1. Press PTY SEARCH while listening to an FM station so that Control @ / # buttons work for selecting PTY code. "PTY" and "SELECT" alternate on the display. PTY SEARCH 2. Press Control @ / # until the PTY code you want appears on the display. Each time you press the button, the display gives you the PTY codes described on page 25. PTY SEARCH 3. While searching, "SEARCH" and the selected PTY code alternate on the display. The receiver searches 40 preset channels, stops when it finds the one you have selected, and tunes in that station. PTY SEARCH To continue searching after the first stop: Press PTY SEARCH again while the indications on the display are flashing. If no program is found, "NOTFOUND" appears on the display. Front panel To stop searching any time during the process: Press PTY SEARCH while searching. Page 24 English DISPLAY MODE When pressing DISPLAY MODE on the remote control: Make sure that you have selected FM station using the remote control only. If not, the DISPLAY MODE button does not work for tuner operation. (Pressing TUNER (on the remote mode section of the inside panel) activates the remote control for tuner operation. ) English From the remote control: Before starting the procedure below, make sure you have selected FM station only using the remote control. If not, the following RDS operating buttons do not work for tuner operation. (Pressing TUNER (on the remote mode section of the inside panel) activates the remote control for tuner operation. ) PTY SEARCH 1. [. . . ] Speaker signal cables are not connected properly. Check speaker wiring and reconnect if necessary. The balance is set to one extreme. Continuous hiss or buzzing during FM reception. Connect an outside FM antenna or contact your dealer. [. . . ]