User manual JVC RX-884R

[. . . ] AUDIO/VIDEO CONTROL RECEIVER AUDIO/VIDEO-RECEIVER MIT STEUEREINHEIT AMPLI/TUNER DE COMMANDE AUDIO/VIDEO GEINTEGREERDE AUDIO/VIDEO-VERSTERKER RECEPTOR DE CONTROL DE AUDIO/VÍDEO RICEVITORE DI CONTROLLO AUDIO/VIDEO RX-884RBK RM-SR884RU REMOTE CONTROL TV/CATV /DBS VCR1 ANALOG AUDIO /DIGITAL DVD VCR1 VCR2 VIDEO CD TAPE/MD PHONO CNTR TONE FM/AM TV/DBS CNTR MENU 1 SURROUND TEST ENTER MODE 2 5 REAR R 3 REAR L MASTER VOLUME 4 SOUND EFFECT CONTROL 6 9 +10 100+ RX-884R AUDIO/VIDEO CONTROL RECEIVER DIGITAL ­ STANDBY 7/P CD DISC SEA MODE 8 0 E + SUBWOOFER DOLBY SURROUND DVD CD 10 AUDIO/TV /VCR RETURN FM MODE/MUTE TV SOUND/DBS PHONO VOLUM CATV /DBS VCR 1 EON TA/NEWS/INFO TAPE/MD STANDBY/ON VCR 2 PTY SEARCH DISPLAY MODE FM CHANNE E MUT ­ RCH SEA PTY PLAY L POWER VIDEO AM PTY + FF / ¢ PTY / RE 4 W _ ON -- OFF MULTI JOG DSP MODE SEA MODE DIGITAL INPUT FM/AM TUNNING TUNER PRESET SOURCE SELECTOR STOP REC PAUSE MODE E DISPLAY TV VOLUM TUNER/SEA MEMORY FM MODE VIDEO S-VIDEO VIDEO L AUDIO R TV/VID EO SPEAKERS PHONES 1 2 BALANCE/SURROUND ADJUST SEA ADJUST SETTING SOUND SELECT LOUDNESS ONE TOUCH OPERATION CONTROL VCR1 TAPE SET EXIT INPUT ATT. SOURCE NAME COMPULINK Remote ENHANCED COMPULINK CONTROL SYSTEM N SC L O REEN CO N TR O DIGITAL INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. [. . . ] LS: Lights when the test tone comes out of the left rear speaker. IMPORTANT: · Output the test tone while playing back an audio source. With the DVD digital input selected as the source, no test tone may come out while no signal is input to this receiver. · Test tone comes out even while playing back a source encoded with Dolby Digital. In this case, the PRO LOGIC indicator lights up on the display. CNTR MENU Notes: · You can adjust the speaker output levels and center tone without outputting the test tone. · You cannot adjust the center speaker output level when "CENTER SPK" is set to "NONE" (see page 20). · You cannot adjust the rear speaker levels when "REAR SPK" is set to "NONE" (see page 20). 5. Adjust the speaker output levels as follows: · To adjust the center speaker level, press CNTR +/­. · To adjust the left rear speaker level, press REAR·L +/­. · To adjust the right rear speaker level, press REAR·R +/­. ENTER 2 REAR L 3 REAR R 5 6 8 9 6. Press CNTR TONE to select the center tone level you want. The center tone adjustment affects the mid-frequency range, which the human voice is mostly made up of. Each time you press the button, the display changes to show the following: SOFT2 SOFT1 FLAT SHARP1 TEST 4 CNTR TONE Note: 1 The center tone cannot be adjusted when "CENTER SPK" is set to "NONE" (see page 20). SHARP2 Adjusted levels are also shown on the equalizer display. This CNTR means this adjustment can be applied to the center speaker only. (Example: When "FLAT" is selected. ) SEA CNTR 100 1k 10k To make the dialogue clearer, select "SHARP1" (little) or "SHARP2" (much). To make the dialogue softer, select "SOFT1" (little) or "SOFT2" (much). When "FLAT" is selected, no adjustment is applied. To cancel the Surround mode Press SURROUND MODE repeatedly until "OFF" appears. 41 On the front panel: You can also use the buttons on the front panel to adjust the Dolby Digital and Dolby Pro Logic modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back. Select and play the source encoded with Dolby Digital (bearing the mark DOLBY SURROUND ). ) or with Dolby Surround (bearing the mark · When you play back the source encoded with Dolby Digital and select the digital input for that source, the Y DIGITAL indicator lights up on the display. DIGITAL Notes: · To enjoy the software encoded with Dolby Digital, you must connect the source component using the digital terminal on the rear of this receiver. · When the signals come into this receiver through the analog connection from the source component, "PRO LOGIC" is automatically selected. · The Surround mode is not used with the other DSP modes such as the DAP mode and 3D-PHONIC mode. When the Surround mode is turned on, the other DSP mode, if used, will be turned off. 2. [. . . ] 87. 5 MHz to 108. 0 MHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monaural . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. 7 dBf (1. 2 µV/75 ohms) 50 dB Quieting Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monaural . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]