User manual JVC RX-D201S

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-D201S INSTRUCTIONS LVT1320-008A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] Auto Function mode works whether or not the receiver is on. When the receiver is off, turning on a video component turns on the receiver, then the video component is selected as the source. You need to select the source manually. VIDEO <CMPNT> Select when connecting the video component to the component video input jacks. Initial setting: VIDEO <S/C> MODE <MANUAL> Initial setting: MODE <MANUAL> When "MODE <AUTO1>" or "MODE <AUTO2>" is selected, the AUTO MODE indicator lights up on the display. NOTE When selecting VCR as the source, only turning on the VCR may not activate "MODE <AUTO1>. " If this happens, you may need to start playback to activate Auto Function mode. 20 Sound adjustments Operating procedure 1, 7 3, 5 2, 4 On the front panel: You can make sound adjustment to your preference after completing basic setting. There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. Ex. : When adjusting subwoofer output level. Basic adjustment items You can adjust the following items. You cannot select the items which is not available with the current setting. Items SUBWFR LVL* 1 1 Press ADJUST. MULTI JOG now works for the sound adjustment. To do Adjust the subwoofer output level. (22) Adjust the left front speaker output level. (22) Adjust the right front speaker output level. (22) Adjust the center speaker output level. (22) Adjust the left surround speaker output level. (22) Adjust the right surround speaker output level. (22) Adjust the surround back speaker output level. (22) Adjust the left surround back speaker output level. (22) Adjust the right surround back speaker output level. (22) Adjust the equalization pattern of each band. (22) 2 Turn MULTI JOG until the item you want to adjust appears on the display. As you turn MULTI JOG, the adjustment items change as follows: ANALOG L S. WFR R FRONT L LVL* * 12 FRONT R LVL*1*2 CENTER LVL*1*2 SURR L LVL* * 12 SURR R LVL*1*2 S BACK LVL*1*2 S BACK L LVL*1*2 S BACK R LVL*1*2 D EQ 63Hz*1 D EQ 250Hz*1 D EQ 1kHz*1 D EQ 4kHz*1 D EQ 16kHz*1 BASS BOOST INPUT ATT EFFECT*1 ROOM SIZE LIVENESS PANORAMA CENTER WIDTH SUBWFR LVL FRONT R LVL SURR L LVL S BACK LVL S BACK R LVL D EQ 250Hz D EQ 4kHz BASS BOOST EFFECT LIVENESS CENTER WIDTH CENTER GAIN CENTER ALIGN FRONT L LVL CENTER LVL SURR R LVL S BACK L LVL D EQ 63Hz D EQ 1kHz D EQ 16kHz INPUT ATT ROOM SIZE PANORAMA DIMENSION CENTER TONE (Back to the beginning) Boost the bass level. (23) Attenuate the input level of analogue source. (23) Select the room size for your virtual listening room. [. . . ] Check speaker wiring and reconnect if necessary (see page 6) after unplugging the power cord. This is not a malfunction. Power "OVER HEAT" flashes on the display, then the receiver turns off. The receiver is overloaded because of high volume or long time usage. No sound from speakers. Speaker signal cables are not connected. Connections are incorrect. Muting is activated. Sound An incorrect input mode (analogue or digital) is selected. Speaker signal cables are not connected properly. [. . . ]