User manual JVC RX-D211SJ-RX-D211 Instruction Manual

[. . . ] AUDIO / VIDEO CONTROL RECEIVER RX-D211S / RX-D212B INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT1557-001A [J] Warnings, Cautions, and Others Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION Changes or modifications not approved by JVC could void the user's authority to operate the equipment. [. . . ] SUBWFR <YES> Select when you have connected a subwoofer. The subwoofer indicator ( S. WFR ) lights up on the display. You can adjust the subwoofer output level (see page 27). Select when you have disconnected a subwoofer. Selecting this changes the front speaker size to "LRG" (see below). 1 Press SETTING. MULTI JOG now works for the setting operation. SUBWFR <NO> 2 Turn MULTI JOG until the item you want to set appears on the display. · As you turn MULTI JOG, the setting items change as follows: ANALOG L S. WFR R Initial setting: SUBWFR <NO> Setting the speaker size--FRONT SPK (front speakers), CENTER SPK (center speaker), SURROUND SPK (surround speakers), S BACK SPK (surround back speakers) Register the sizes of all the connected speakers. QUICK SPK SET FRONT SPK SURROUND SPK S BACK OUT FRONT L DIST CENTER DIST SURR R DIST S BACK L DIST EX/ES/PLIIx SUBWOOFER OUT LFE ATT DIGITAL IN 1 DIGITAL IN 3 VCR VIDEO IN (Back to the beginning) SUBWOOFER CENTER SPK S BACK SPK DIST UNIT FRONT R DIST SURR L DIST S BACK DIST S BACK R DIST DUAL MONO CROSSOVER MIDNIGHT MODE DIGITAL IN 2 DVD VIDEO IN DBS VIDEO IN <LRG> (large) <SML> (small) <NO> Initial setting: Select when the cone speaker size is larger than 12 cm (4 3/4 inches). Select when the cone speaker size is smaller than 12 cm (4 3/4 inches). Select when you have disconnected a speaker. (Not selectable for the front speakers. ) <LRG> (for the front speakers) <SML> (for other speakers) Setting the surround back speaker(s)--S BACK OUT Register the number of surround back speaker(s). SB OUT <1SPK> Select when you use one surround back speaker. SB OUT <2SPK> Select when you use two surround back speakers. Initial setting: SB OUT <2SPK> NOTES · If you have selected "SML (small)" for the front speaker size, you cannot select "LRG (large)" for other speakers. · When "SUBWOOFER" is set to "SUBWFR <NO>, " the front speaker size is fixed to "LRG" (and you cannot select "SML"). · When "SURROUND SPK" is set to "SML (small), " you cannot select "LRG (large)" for the surround back speaker. · When "SURROUND SPK" is set to "NO, " the surround back speaker is fixed to "NO. " · When "S BACK SPK" is set to "NO, " you cannot select "S BACK OUT. " · When "SB OUT" is set to "<1SPK>, " connect the surround back speaker to the left surround back speaker terminal (see page 6). No sound comes from the surround back speaker if you connect it to the right surround back speaker terminal. 3 Press SET. The current setting of the selected item appears. ANALOG L S. WFR R 4 Turn MULTI JOG to select the appropriate setting. ANALOG L S. WFR R DVR/DVD TV Your setting is stored. DBS VCR 5 Press SET. 6 Repeat steps 2 to 5 to set other items if necessary. 7 Press SETTING. The source indication resumes on the display. 22 Setting the speaker distance The distance from your listening point to the speakers is one of the important elements to obtain the best possible sound effect from the Surround/DSP modes. By referring to the speaker distance, the receiver automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you at the same time. 7 Measuring unit--DIST UNIT Select which measuring unit you use. D UNIT <meter>Select to set the distance in meters. D UNIT <feet> Select to set the distance in feet. Activating the EX/ES/PLIIx setting-- EX/ES/PLIIx Depending on this setting, available Surround modes for digital multi-channel software vary--EX/ES/PLIIx reproduction or 5. 1channel reproduction. Select an appropriate setting for your enjoyment. · For details about relation between EX/ES/PLIIx setting and available Surround mode, see page 33. [. . . ] Check speaker wiring and reconnect if necessary (see page 6) after unplugging the power cord. This is not a malfunction. Power "OVER HEAT" flashes on the display, then the receiver turns off. The receiver is overloaded because of high volume or long time usage. No sound from speakers. Speaker signal cables are not connected. Connections are incorrect. Muting is activated. Sound An incorrect input mode (analog or digital) is selected. Speaker signal cables are not connected properly. [. . . ]