User manual JVC RX-D301S

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-D301S / RX-D302B INSTRUCTIONS LVT1321-008A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] * The LFE signals are emitted only when playing the following software with the LFE signals: -Dolby Digital multi channel software -DTS multi channel software When playing analogue source or linear PCM software, no LFE signals are emitted. 21 Using the Midnight mode --MIDNIGHT MODE You can enjoy a powerful sound at night using the Midnight mode. When the Midnight mode is activated, the MIDNIGHT indicator lights up on the display. MIDNIGHT <OFF> Select when you want to enjoy surround with its full dynamic range. (No effect applied. ) Select when you want to reduce the dynamic range a little. Select when you want to apply the compression effect fully (useful at night). NOTES You cannot assign the same component for different terminals. The priority order for assignment is as follows: "DIGITAL IN 1" > "DIGITAL IN 2" > "DIGITAL IN 3. " Ex. : When "DIGITAL IN 1" is set to "DVR/DVD. " DIGITAL IN 1 DVR/DVD VIDEO VCR TV For "DIGITAL IN 2, " "VIDEO, " "VCR, " and "TV" are selectable. In this case, "VCR" is selected. DIGITAL IN 2 DVR/DVD VIDEO MIDNIGHT <1> MIDNIGHT <2> VCR TV For "DIGITAL IN 3, " "VIDEO" and "TV" are selectable. DIGITAL IN 3 DVR/DVD VIDEO : Selectable Initial setting: MIDNIGHT <OFF> VCR TV From the remote control: Press MIDNIGHT repeatedly to select either one of the above. : Not selectable Setting "DIGITAL IN 1" affects "DIGITAL IN 2" and "DIGITAL IN 3" settings. When you have changed "DIGITAL IN 1, " confirm the components assigned to "DIGITAL IN 2" and "DIGITAL IN 3. " 1 4 7 10 2 5 8 0 3 6 9 10 Setting the Auto Function mode --AUTO MODE The source will be selected automatically simply by turning on a video component. This function takes effect for the video components connected to the receiver using the SCART cable--DVR/DVD and VCR. Auto Function mode works as follows: When a video component is turned on, the receiver selects the video component as the source (and the TV input is changed automatically). When a video component currently selected as the source is turned off, the receiver changes the source to the video source previously selected--DVR/DVD, VCR, or VIDEO. MODE <AUTO1> MODE <AUTO2> Auto Function mode works when the receiver is on. Auto Function mode works whether or not the receiver is on. When the receiver is off, turning on a video component turns on the receiver, then the video component is selected as the source. You need to select the source manually. NOTE When "DVD MULTI" is selected as the source, this function is not available. Setting the digital input (DIGITAL IN) terminals--DIGITAL IN 1/2/3 When you use the digital input terminals, register what components are connected to which terminals--DIGITAL IN 1/2/3 (see page 11) so that the correct source name will appear when you select the digital source. Select one of the following components for each terminal: DVR/DVD For the DVD player (or DVD recorder). VIDEO VCR TV For the component connected to the VIDEO IN jacks on the rear of the receiver. For the TV. MODE <MANUAL> Initial setting: MODE <MANUAL> When "MODE <AUTO1>" or "MODE <AUTO2>" is selected, the AUTO MODE indicator lights up on the display. NOTE When selecting VCR as the source, only turning on the VCR may not activate "MODE <AUTO1>. " If this happens, you may need to start playback to activate Auto Function mode. Initial setting: DVR/DVD (for "DIGITAL IN 1") VIDEO (for "DIGITAL IN 2") TV (for "DIGITAL IN 3") 22 Selecting the component video input mode--DVD VIDEO IN/VCR VIDEO IN/ VIDEO VIDEOIN When you use the component video inputs for connecting the DVD recorder (or DVD player), VCR, or other video components (STB, for example), register the type of video input jacks. If you have not selected appropriate video input jacks, you cannot view the playback picture on the TV. [. . . ] Speaker signal cables are not connected properly. When you use the digital coaxial connection, the sounds may be intermittently distorted by the outside noise such as a lightning discharge but the sound will be restored automatically. RGB signals are input when Y/C SEPARATE is activated. The remote control is not ready for your intended operation. [. . . ]