User manual JVC RX-D402BJ-RX-D402 Instruction Manual

[. . . ] AUDIO / VIDEO CONTROL RECEIVER RX-D401S / RX-D402B INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT1436-001A [J] Warnings, Cautions, and Others Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For Canada/pour le Canada CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] For the TV. Initial setting: DVR/DVD (for "DIGITAL IN 1") DBS (for "DIGITAL IN 2") VCR (for "DIGITAL IN 3") NOTES · You cannot assign the same component for different terminals. The priority order for assignment is as follows: "DIGITAL IN 1" > "DIGITAL IN 2" > "DIGITAL IN 3. " Ex. : When "DIGITAL IN 1" is set to "DVR/DVD. " DIGITAL IN 1 DVR/DVD Setting the low frequency effect attenuator--LFE ATT If the bass sound is distorted while playing back software encoded with Dolby Digital or DTS, set the LFE level to eliminate distortion. · This function takes effect only when the LFE signals come in. LFE <0dB> Normally select this. DBS VCR TV For "DIGITAL IN 2, " "DBS, " "VCR, " and "TV" are selectable. · In this case, "VCR" is selected. DIGITAL IN 2 DVR/DVD LFE <­10dB> Select when the bass sound is distorted. Initial setting: LFE <0dB> DBS VCR TV For "DIGITAL IN 3, " "DBS" and "TV" are selectable. DIGITAL IN 3 DVR/DVD DBS VCR TV Using the Midnight mode --MIDNIGHT MODE You can enjoy a powerful sound at night using the Midnight mode. When the Midnight mode is activated, the MIDNIGHT indicator lights up on the display. MIDNIGHT <OFF> Select when you want to enjoy surround with its full dynamic range. (No effect applied. ) Select when you want to reduce the dynamic range a little. Select when you want to apply the compression effect fully (useful at night). : Selectable : Not selectable · Setting "DIGITAL IN 1" affects "DIGITAL IN 2" and "DIGITAL IN 3" settings. When you have changed "DIGITAL IN 1, " confirm the components assigned to "DIGITAL IN 2" and "DIGITAL IN 3. " MIDNIGHT <1> MIDNIGHT <2> Initial setting: MIDNIGHT <OFF> From the remote control: Press MIDNIGHT repeatedly to select either one of the above. 1 4 7 10 2 5 8 0 3 6 9 10 25 Setting the Audio delay level --AUDIO DELAY Synchronization between audio and video reproduction can be possibly disturbed because video signal decoding is timeconsuming compared to the audio signal decoding. On this setting, you can correct synchronization between video and audio signals by delaying the audio signal timing. Adjustable range: OFF and 10 ms to 100 ms (in 10 ms intervals) Initial setting: ADELAY OFF> Selecting the source for HDMI terminal and COMPONENT VIDEO jacks--HDMI SELECT/CMPNT SELECT When you connect a VCR or DBS to the "VCR (DBS) IN" terminal in HDMI terminal or COMPONENT VIDEO jacks on the rear of the receiver, you need to select either "VCR" or "DBS" according to the component you connect. If you have not selected appropriate source, you cannot view the playback picture on the TV. For the HDMI terminal: HDMI <VCR> <DBS> Memorizing the volume level for each source--ONE TOUCH OP This receiver memorizes some settings separately for each source. In addition, you can store the volume level for each source with the other memorized settings (see page 17). · This receiver memorizes the volume level ­ when you turn off the power, and ­ when you change the source. ONE TOUCH <ON> Select to store the volume level separately for each source. (The ONE TOUCH OPERATION indicator lights up on the display. ) ONE TOUCH <OFF> Select this not to store the volume level. Initial setting: ONE TOUCH <OFF> To recall the volume level With the ONE TOUCH OPERATION indicator lit, the volume level for the currently selected source is recalled when the source is selected. [. . . ] A HDMI cable longer than 5 m (15 ft) is used. Sounds are intermittently distorted by the outside noise such as a lightning discharge. No picture on the TV screen. HDMI signals do not come on. Select the correct setting (see page 17 or 26). Check the video or audio format of the signal to see if it is compatible with this receiver and/or TV. Disconnect the HDMI cable and connect it again. [. . . ]