User manual JVC RX-D702B

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-D701S / RX-D702B INSTRUCTIONS LVT1437-001A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] (Not selectable for the front speakers. ) 7 Setting subwoofer information--SUBWOOFER Select whether you have connected a subwoofer or not. SUBWOOFER: YES Select when you have connected a subwoofer. The subwoofer indicator ( S. WFR ) lights up on the display. You can adjust the subwoofer output level (see page 37). Select when you have disconnected a subwoofer. Selecting this changes the front speaker size to "LARGE" (see the right column). SUBWOOFER: NO Initial setting: LARGE (for the front speakers) SMALL (for other speakers) Initial setting: SUBWOOFER: NO 28 7 Setting the surround back speaker(s) --S BACK OUT Register the number of the surround back speaker(s). S BACK OUT: 1SPK S BACK OUT: 2SPK Select when you use 1 surround back speaker. Select when you use 2 surround back speakers. C FL FR 3. 3 m (11 ft) 3. 0 m (10 ft) 2. 7 m (9 ft) 2. 4 m (8 ft) 2. 1 m (7 ft) Initial setting: S BACK OUT: 2SPK SL NOTES If you have selected "SMALL" for the front speaker size, you cannot select "LARGE" for other speakers. When "SUBWOOFER" is set to "SUBWOOFER: NO, " the front speaker size is fixed to "LARGE" (and you cannot select "SMALL"). When "SURR SPK" is set to "SMALL, " you cannot select "LARGE" for the surround back speaker. When "SURR SPK" is set to "NO, " the surround back speaker is fixed to "NO. " When "S BACK SPK" is set to "NO, " you cannot select "S BACK OUT. " When "S BACK OUT" is set to "S BACK OUT: 1SPK, " connect the surround back speaker to the left surround back speaker terminal (see page 8). No sound comes from the surround back speaker if you connect it to the right surround back speaker terminal. SR SBL SBR In this case, set the distance as follows: Left front speaker (FL): "FL SPK DIST. : 3. 0m (10ft)" Right front speaker (FR): "FR SPK DIST. : 3. 0m (10ft)" Center speaker (C): "C SPK DIST. : 3. 0m (10ft)" Left surround speaker (SL): "SL SPK DIST. : 2. 7m (9ft)" Right surround speaker (SR): "SR SPK DIST. : 2. 7m (9ft)" Left surround back speaker (SBL): "SBL SPK DIST. : 2. 4m (8ft)" Right surround back speaker (SBR): "SBR SPK DIST. : 2. 4m (8ft)" 7 Setting the speaker distance The distance from your listening point to the speakers is one of the important elements to obtain the best possible sound effect from the Surround/DSP modes. By referring to the speaker distance, the receiver automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you at the same time. 7 Measuring unit--DISTANCE UNIT Select which measuring unit you use. DISTANCE UNIT: meter Select to set the distance in meters. DISTANCE UNIT: feet Select to set the distance in feet. NOTES You cannot set the speaker distance for the speakers you have set to "NO. " If you have selected "S BACK OUT: 1SPK" for "S BACK OUT" (see the left column), "SB SPK DIST. " appears instead of "SBL SPK DIST. " and "SBR SPK DIST. " Initial setting: DISTANCE UNIT: meter 7 Speaker distance-- FL SPK DIST. (for the left front speaker), FR SPK DIST. (for the right front speaker), C SPK DIST. (for the left surround speaker), SR SPK DIST. (for the right surround speaker), SBL SPK DIST. (for the left surround back speaker), SBR SPK DIST. (for the right surround back speaker) Adjustable range: 0. 3 m to 9. 0 m in 0. 3 m intervals (1 ft to 30 ft in 1 ft intervals) Initial setting: 3. 0 m (10 ft) for all speakers 29 Activating the EX/ES/PLIIx setting--EX/ES/ PLIIx Depending on this setting, available Surround modes for digital multi-channel software vary--EX/ES/PLIIx reproduction or 5. 1channel reproduction. [. . . ] Select the correct setting. Set the video input setting to the setting other than "HDMI" or "RGB" (see page 20). Check the video or audio format of the signal to see if it is compatible with this receiver and/or TV. Connect a HDCP-compatible TV (see page 10). Disconnect the HDMI cable and connect it again. [. . . ]