User manual JVC RX-DP9VBKJ-RX-DP9

[. . . ] AUDIO/VIDEO CONTROL RECEIVER RX-DP9VBK STANDBY ON TV/CATV/DBS VCR 1 STANDBY/ON STANDBY/ON DVD DVD MULTI PHONO CD VCR 1 VCR 2 TAPE/MD CDR TV/DBS ANALOG/DIGITAL VIDEO FM AM EFFECT INPUT SOUND 1 4 7/P 10 RETURN 2 5 8 0 FM MODE 3 ROOM SIZE 6 LIVENESS 9 WALL +10 100+ MASTER VOLUME TEST SURROUND ON/OFF DSP MODE THX ON/OFF STANDBY LINE DIRECT CC CONVERTER CC CONVERTER DIMMER SLEEP DIMMER TV CATV/ DBS STANDBY/ON DOOR UP / REW PLAY TUNING STOP FF/ UP PAUSE DOWN REC RX-DP9V DOOR DOWN TV/VIDEO TV VOL CHANNEL VOLUME MUTING AUDIO/VIDEO CONTROL RECEIVER SETUP MENU ADJUST MENU DIGITAL TEXT DISPLAY SET SURROUND DIGITAL DVD MENU EXIT PHONES S-VIDEO RM-SRXDP9J REMOTE CONTROL A/V CONTROL RECEIVER VIDEO L--AUDIO--R VIDEO INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0722-001A [J] Warnings, Cautions and Others CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. [. . . ] · Test tone will be heard about three seconds after you select "AUTO" or "MANUAL. " AUTO : When this is selected, the test tone comes out of all the activated speakers in sequence (for 2 seconds each). The test tone comes out of the activated speakers in the following sequence: Adjusting the Parametric Equalizer --PARAMETRIC EQ (2) PARAMETRIC EQ FRONT CENTER SURROUND SURROUND BACK :ENTER :BACK On this submenu, you can adjust equalization patterns according to your preference. First, select the signal channel (speaker) you want to adjust, then move to its adjustment screen. Left front speaker = Center speaker = Right front speaker = Right surround speaker = Right surround back speaker = Left surround back speaker = Left surround speaker = Subwoofer = (Back to the beginning) Notes: · If "NO" or "NONE" is selected for a speaker on the SPEAKER SETTING submenu (see page 29), you cannot select the corresponding channel. · If THX Surround or DVD MULTI playback mode is in use, this submenu is not available. MANUAL : When this is selected, the test tone comes out of only the speaker you select. (To select the speaker, see the right column. ) OFF : Select this to stop the test tone. 37 7 Adjustment procedure on this submenu 1 Press fi or % (DOWN or UP) to select the channel-- FRONT, CENTER, SURROUND, or SURROUND BACK, then press SET. The adjustment screen of the selected item appears. Press fi or % (DOWN or UP) to select an item you want to adjust on the selected adjustment screen. Press # or @ (RIGHT or LEFT) to adjust the item. · Once one of the sound levels--"BASS LEVEL, " "MID LEVEL" and "TREBLE LEVEL"--is adjusted, the PARAMETRIC EQ indicator lights up on the display. Repeat steps 2 and 3 to adjust the other items on the same adjustment screen. The PARAMETRIC EQ submenu appears again. Repeat steps 1 to 5 to adjust the other channels. Adjusting the DSP Parameters --DSP PARAMETER (3) DSP PARAMETER EFFECT LEVEL :3 ROOM SIZE :3 LIVENESS :3 WALL TYPE :3 SEAT POSITION:1 :OPERATE :BACK 2 3 On this submenu, you can adjust DSP parameters. · This submenu is available only when the DSP mode* is on, and the settings made apply only to the DSP mode* (*except All Channel Stereo). Note: When the front speakers are deactivated, you cannot adjust the DSP parameters. 4 5 6 7 Adjusting the DSP parameters Select and adjust the following parameters: EFFECT LEVEL: Adjust the DSP effect level. As the number increases, the DSP effect becomes stronger. (Normally select "3. " Adjustable range: 1 to 5) ROOM SIZE: Adjust the virtual room size. As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally select "3. " Adjustable range: 1 to 5) LIVENESS: Adjust the liveness effect. As the number increases, the attenuation level of reflections over time decreases so that acoustics change from "Dead" to "Live. " (Normally select "3. " Adjustable range: 1 to 5) WALL TYPE: Adjust the wall type. As the number increases, the hardness of the wall to be simulated seems to become "soft" to "hard. " (Normally select "3. " Adjustable range: 1 to 5) SEAT POSITION: Select this to either 1 or 2 according to your preference as if you change your seat in a theater, hall, recital hall, church, etc. To cancel the adjustment, set all the sound levels--"BASS LEVEL, " "MID LEVEL" and "TREBLE LEVEL"--to "0 dB. " The PARAMETRIC EQ indicator goes off. 7 Adjustment screen On these adjustment screens, you can adjust the following items for each channel signal. PEQ FRONT BASS FREQ : 100Hz BASS LEVEL : 0dB MID FREQ : 1. 0kHz MID LEVEL : 0dB TREBLE FREQ :10. 0kHz TREBLE LEVEL: 0dB PEQ SURROUND BASS FREQ : 100Hz BASS LEVEL : 0dB MID FREQ : 1. 0kHz MID LEVEL : 0dB TREBLE FREQ :10. 0kHz TREBLE LEVEL: 0dB PEQ CENTER BASS FREQ : 100Hz BASS LEVEL : 0dB MID FREQ : 1. 0kHz MID LEVEL : 0dB TREBLE FREQ :10. 0kHz TREBLE LEVEL: 0dB PEQ SURR BACK BASS FREQ : 100Hz BASS LEVEL : 0dB MID FREQ : 1. 0kHz MID LEVEL : 0dB TREBLE FREQ :10. 0kHz TREBLE LEVEL: 0dB Adjusting the Center Channel --CENTER CHANNEL (4) CENTER CHANNEL CENTER EQ : OFF CENTER ALINMENT: OFF BASS FREQ* : Select the center frequency to adjust bass sounds from --63 Hz, 80 Hz, 100 Hz (initial), 125 Hz, 160 Hz, 200 Hz, 250 Hz, 320 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1. 0 kHz : Adjust the enhancement level for bass sounds (with in the range of +6 dB to ­6 dB). : Select the center frequency to adjust middle-range sounds from --250 Hz, 320 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1. 0 kHz (initial), 1. 25 kHz, 1. 6 kHz, 2. 0 kHz, 2. 5 kHz, 3. 2 kHz, 4. 0 kHz : Adjust the enhancement level for middlerange sounds (with in the range of +6 dB to ­6 dB). :OPERATE :BACK BASS LEVEL MID FREQ* On this submenu, you can set center channel signal adjustment for the DSP modes. · This submenu is available only when the DSP mode* is on, and the settings made apply only to the DSP mode* (*except All Channel Stereo). 7 Cutting off the high frequency range in the center channel Cut off the high frequency range signals in the center channel. [. . . ] All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis. WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 537-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. [. . . ]