User manual JVC RX-E11SB

[. . . ] HOME CINEMA CONTROL CENTER RX-E11S/RX-E12B INSTRUCTIONS LVT1301-005A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] Select to play back both the main and subchannels (Ch 1/Ch 2). * Signal indicators "L" and "R" light up while playing back these channels. D MONO:MAIN D MONO: ALL Initial setting: D MONO:MAIN * Dual Mono signals can be heard from the following speakers--L (left front speaker), R (right front speaker), and C (center speaker), with respect to the current Surround setting: With Surround Activated Dual Mono setting Without Surround L SUB MAIN ALL Ch 2 Ch 1 Ch 1 R Ch 2 Ch 1 Ch 2 L Center speaker setting SML/LRG C Ch 2 Ch 1 Ch 1+Ch 2 R L Ch 2 Ch 1 NO R Ch 2 Ch 1 Ch 1+Ch 2 Ch 1+Ch 2 NOTE The Dual Mono format is not identical with bilingual broadcasting for TV programs. So this setting does not take effect while watching such bilingual programs. 18 Setting the digital input (DIGITAL IN) terminals--DIGITAL IN1/2 When you use the digital input terminals, register what components are connected to which terminals--DIGITAL IN1/2 (see page 9) so that the correct source name will appear when you select the digital source. For DIGITAL IN 1(DVR/DVD) terminal: EQ C. TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE PL ATT LPCM LCR HP DOLBY D S . WFR LFE NEO : 6 MHz DSP 3D DTS AAC LS SB RS AUTO SR kHz 96 / 24 NOTES This function does not take effect in the following cases: While playing an analogue source, While selecting any of DSP modes (see page 31), or one of the fixed digital decode mode--"DGTL D. D. " or "DGTL DTS" (see page 11), and While listening with the headphones. If you press SURROUND with Auto Surround activated, Auto Surround will be canceled temporarily for the currently selected source. Auto Surround setting will be restored in the following cases: When you turn the receiver off and on, When you change the source, When you change the analogue/digital input, and When you select "AUTO SR: ON" again. DVR/DVD VIDEO VCR (Back to the beginning) TV For DIGITAL IN 2(VIDEO) terminal: EQ C. TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST AUTO MUTING SLEEP AUTO MODE PL ATT LPCM LCR HP DOLBY D S . WFR LFE NEO : 6 MHz DSP 3D DTS AAC LS SB RS AUTO SR kHz 96 / 24 Setting the Auto Function mode --AUTO MODE The source will be selected automatically simply by turning on a video component. This function takes effect for the video components connected to the receiver using the SCART cable--DVR/DVD and VCR. Auto Function mode works as follows: When a video component is turned on, the receiver selects the video component as the source (and the TV input is changed automatically). When a video component currently selected as the source is turned off, the receiver changes the source to the video source previously selected--DVR/DVD, VCR, or VIDEO. MODE: AUTO1 Auto Function mode works when the receiver is turned on or when TV Direct is activated. VIDEO* VCR* TV* (Back to the beginning) DVR/DVD* * The one selected for "DIGITAL IN1" will be skipped. DVR/DVD For DVD player (or DVD recorder). VIDEO VCR TV For the component connected to the VIDEO IN jack on the rear of the receiver. For TV. Initial setting: DVR/DVD (for "DIGITAL IN1") VIDEO (for "DIGITAL IN2") MODE: AUTO2 Setting Auto Surround--AUTO SURRND You can enjoy the Surround mode simply by selecting the source (with digital input selected for that source). Auto Surround also works when the input mode changes from analogue to digital. For details about the Surround/DSP modes, see pages 29 to 31. Select "AUTO SR: ON" when activating Auto Surround. AUTO SR: ON The AUTO SR indicator lights up on the display. If a multi-channel signal comes in, an appropriate Surround mode will be turned on. If a Dolby Digital 2-channel or DTS 2-channel signal with surround signal comes in, "PLII MOVIE" will be selected. [. . . ] \ Speakers are overloaded because of a short circuit at the speaker terminals. If speaker wiring is not short-circuited, contact your dealer. \ The receiver is overloaded because of a high voltage. Consult your dealer after unplugging the power cord. [. . . ]