User manual JVC RX-F10S

[. . . ] HOME CINEMA CONTROL CENTER RX-F10S INSTRUCTIONS LVT1163-007A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] Ch 2 Ch 1 Ch 1 R Ch 2 Ch 1 Ch 2 L Initial setting: EX/ES :AUTO From the remote control: Set the mode selector to "AUDIO/TV/VCR/STB. " Press EX/ES repeatedly to select either one of above. Dual Mono setting Center speaker setting SML/LRG C Ch 2 Ch 1 Ch 1+Ch 2 R L Ch 2 Ch 1 NO R Ch 2 Ch 1 Ch 1+Ch 2 Ch 1+Ch 2 Basic settings NOTES NOTES When "SURRND SPK" is set to "NO" (see page 18), this function is not available. When "S BACK SPK" is set to "NO" (see page 18), the Virtual Surround Back (see page 34) is applied for EX/ES (6. 1-channel) reproduction. For some Dolby Digital EX software, Dolby Digital 5. 1-channel reproduction ("DOLBY D") may be applied even though you have selected 6. 1-channel reproduction to apply. Using the Midnight mode --MIDNIGHT M. You can enjoy a powerful sound at night using the Midnight mode. NIGHT :OFF NIGHT : 1 NIGHT : 2 Select when you want to enjoy surround with its full dynamic range. (No effect applied. ) Select when you want to reduce the dynamic range a little. Select when you want to apply the compression effect fully (useful at night). Initial setting: NIGHT :OFF From the remote control: Set the mode selector to "AUDIO/TV/VCR/STB. " Press SOUND, then press MIDNIGHT repeatedly to select either one of above. NOTE After pressing SOUND, the numeric buttons work for sound adjustments. To use the numeric buttons to operate your target source, press the corresponding source selecting button before operation; otherwise, the remote control may not work as you intend. 20 Setting the digital input (DIGITAL IN) terminals--DIGITAL IN1/2/3 When you use the digital input terminals, register what components are connected to which terminals--DIGITAL IN1/2/3 (see page 11) so that the correct source name will appear when you select the digital source. Select one of the following components for each terminal: DVR/DVD For DVD player (or DVD recorder). VIDEO VCR TV For the component connected to the VIDEO IN jacks on the rear of the receiver. For TV. NOTES This function does not take effect in the following cases: While playing an analogue source, While selecting any of DSP modes (see page 33), or one of the fixed digital decode mode--"DGTL D. D. " or "DGTL DTS" (see page 13), and While listening with the headphones. If you press SURROUND with Auto Surround activated, Auto Surround will be canceled temporarily for the currently selected source. Auto Surround setting will be restored in the following cases: When you turn the receiver off and on, When you change the source, When you change the analogue/digital input, and When you select "AUTO SR: ON" again. Initial setting: DVR/DVD (for "DIGITAL IN1") VIDEO (for "DIGITAL IN2") TV (for "DIGITAL IN3") NOTES You cannot assign the same component for different terminals. The priority order for assignment is as follows: "DIGITAL IN1" > "DIGITAL IN2" > "DIGITAL IN3. " Ex. : When "DIGITAL IN1" is set to "DVR/DVD" DIGITAL IN1 DVR/DVD VIDEO Setting the Auto Function mode --AUTO MODE The source will be selected automatically simply by turning on a video component. This function takes effect for the video components connected to the receiver using the SCART cable--DVR/DVD and VCR. Auto Function mode works as follows: VCR TV When a video component is turned on, the receiver selects the video component as the source (and the TV input is changed automatically). When a video component currently selected as the source is turned off, the receiver changes the source to the video source previously selected--DVR/DVD, VCR, or VIDEO. MODE: AUTO1 MODE: AUTO2 Auto Function mode works when the receiver is turned on or when TV Direct is activated. For "DIGITAL IN2, " "VIDEO, " "VCR, " and "TV" are selectable. In this case, "VCR" is selected. DIGITAL IN2 DVR/DVD VIDEO VCR TV For "DIGITAL IN3, " "VIDEO" and "TV" are selectable. DIGITAL IN3 DVR/DVD VIDEO : Selectable VCR TV : Not selectable Setting "DIGITAL IN1" affects "DIGITAL IN2" and "DIGITAL IN3" settings. When you have changed "DIGITAL IN1, " confirm the components assigned to "DIGITAL IN2" and "DIGITAL IN3. " MODE:MANUAL You need to select the source manually. Setting Auto Surround--AUTO SURRND You can enjoy the Surround mode simply by selecting the source (with digital input selected for that source). [. . . ] An incorrect input mode (analogue or digital) is selected. Speaker signal cables are not connected properly. When you use the digital coaxial connection, the sounds may be intermittently distorted by the outside noise such as a lightning discharge but the sound will be restored automatically. The remote control is not ready for your intended operation. [. . . ]