User manual JVC RX-F31S

[. . . ] HOME CINEMA CONTROL CENTER RX-F31S INSTRUCTIONS LVT1306-007A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] AUTO MODE: AUTO1 Auto Function mode works when the receiver is turned on or when TV Direct is activated. AUTO MODE: AUTO2 Auto Function mode works when the receiver is turned on or off, or when TV Direct is activated. (When a video component is turned on while the receiver is off, TV Direct is activated and the receiver selects the video component as the source. ) AUTO MODE: MANUAL You need to select the source manually. Initial setting: AUTO MODE: MANUAL When "AUTO MODE: AUTO1" or "AUTO MODE: AUTO2" is selected, the AUTO MODE indicator lights up on the display. NOTES When selecting "VCR" as the source, "AUTO MODE: AUTO1" or "AUTO MODE: AUTO2" may not work if you only turn on the VCR. If this happens, you may need to start playback to activate Auto Function mode. When Auto Function mode is set to "AUTO MODE: AUTO2, " the TV Direct may be activated after recovery from a power failure. Initial setting: DVR/DVD (for "DIGITAL IN 1") VIDEO (for "DIGITAL IN 2") TV (for "DIGITAL IN 3") NOTES You cannot assign the same component for different terminals. The priority order for assignment is as follows: "DIGITAL IN 1" > "DIGITAL IN 2" > "DIGITAL IN 3. " "DIGITAL IN 1" can be set to any component. Ex. : When "DIGITAL IN 1" is set to "TV. " DIGITAL IN 1: TV "DVR/DVD, " "VIDEO, " and "VCR" are selectable for "DIGITAL IN 2. " And when "DIGITAL IN 2" is set to "DVR/DVD. " DIGITAL IN 1: TV DIGITAL IN 2: DVR/DVD "VIDEO" and "VCR" are selectable for "DIGITAL IN 3. " Setting "DIGITAL IN 1" affects "DIGITAL IN 2" and "DIGITAL IN 3" settings. When you have changed "DIGITAL IN 1, " confirm the components assigned to "DIGITAL IN 2" and "DIGITAL IN 3. " 24 Selecting the type of the input signal --DVD VIDEO INPUT/VCR VIDEO INPUT When you use the AV IN/OUT (SCART) terminals for connecting the DVD recorder (or DVD player) or VCR, register the type of the input signal. If you have not selected appropriate input signal types, you cannot view the playback picture on the TV. For the DVD recorder or DVD player (DVD VIDEO): DVD VIDEO: RGB/C Select when connecting the DVD recorder (or DVD player) to SCART terminal which receives RGB or composite video signals. DVD VIDEO: S-VIDEO Select when connecting the DVD recorder (or DVD player) to SCART terminal which receives S-video signals. Initial setting: DVD VIDEO: RGB/C For the VCR (VCR VIDEO): VCR VIDEO: RGB/C Select when connecting the VCR to SCART terminal which receives RGB or composite video signals. VCR VIDEO: S-VIDEO Select when connecting the VCR to SCART terminal which receives S-video signals. Initial setting: VCR VIDEO: RGB/C Converting S-video signals into composite video signals--DOWN MIX You can select whether or not to convert S-video signals into composite video signals. DOWN MIX: ON Select to convert S-video signals into composite video signals. DOWN MIX: OFF Select not to use this function. Initial setting: DOWN MIX: OFF The converted signals are output through the AV IN/OUT (SCART) terminals (see page 7) as follows: S-video signals which are input from the S-VIDEO jack of the VIDEO IN terminal and converted into composite video signals can be output from any AV IN/OUT (SCART) terminal. S-video signals which are input from the AV IN/OUT (SCART) terminals and converted into composite video signals can be output through any AV IN/OUT (SCART) terminal except through the same AV IN/OUT (SCART) terminal. NOTES This function is available when satisfying all the following requirements: When a video component is connected to this receiver through using at least one of the connections to input S-video signals. When a video component or the TV is connected to this receiver through at least one of the AV IN/OUT (SCART) terminals to output composite video signals. Either the DVD VIDEO INPUT or the VCR VIDEO INPUT is set to "S-VIDEO" (see left column). [. . . ] The remote control is not ready for your intended operation. There is an obstruction hiding the remote sensor on the receiver. The mode selector is set to the incorrect position. Continuous hiss or buzzing during FM reception. [. . . ]