User manual JVC SR-V10U

[. . . ] VIDEO CASSETTE RECORDER SR-V10U TV CABLE/ DBS MBR SET A/B POWER TV/VCR A. MONITOR DISPLAY 1 4 DBS 2 5 DAILY 3 2 6 WEEKLY 7 C. RESET 8 AUX 9 TIMER 4 CANCEL 0 STOP DATE START CH EXPRESS PROGRAMMING 1 PROG PROG CHECK SP/EP SKIP SEARCH PLAY REW FF REW PLAY FF REC STOP PAUSE POWER ­ + MENU 3 OK TV CH + CH­ /+ PUSH / TURN SHUTTLE PLUS L ­ O V L TV VO + TV REC LINK S VIDEO VIDEO (MONO)L--AUDIO--R SP EP VCR A. DUB 24HR QUICK PROGRAM TV CH ­ DIGITAL TBC/NR INSERT REC PAUSE STOP/EJECT MULTI BRAND REMOTE CONTROL UNIT INSTRUCTIONS For Customer Use: Enter below the Model No. which are located on the rear of cabinet. Retain this information for future reference. [. . . ] (The PlusCode programing numbers are the numbers next to the program in most TV listing. ) VCR Plus+® Timer Programing Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV. 1 Load a cassette POWER 1 4 2 5 8 0 3 2 Make sure the record safety tab is intact. If not, set "REC SAFETY" to "OFF" ( pg. The VCR turns on, and the counter is reset, automatically. You can also record onto a cassette without a record safety tab by covering the hole with adhesive tape before inserting the cassette. 6 9 4 DAILY CANCEL STOP +/­ 34 WEEKLY 2 Access PlusCode No. The clock must be set to access the PRESS NUMBER KEY (0­9) PlusCode No. PRESS (+/­) TO SET If you have not set the EXPRESS PROGRAMMING PRESS (PROG. ) TO END clock, the Main Menu screen appears after an error message is displayed. Refer to page 8 for the Plug & Play setting or page 10 for the clock setting procedure. 7 8 4 6 27 1 3 4 347 3 Enter PlusCode number PLUSCODE NO. Press the appropriate Number keys to input the PlusCode number printed in the TV listings for the TV broadcast you wish to record, then press OK. 123 PRESS NUMBER KEY (0­9) THEN (OK) PRESS (PROG. ) TO END Then; If the Guide Channel Set screen appears -- go to step 4. If the VCR Plus+ Program screen appears -- go to step 5. To make corrections, press CANCEL and input the correct PlusCode number. EN 29 4 Input receiving channel number The guide channel GUIDE CHANNEL SET number, which is GUIDE CH: 12 assigned to the TV or VCR CH : ­ ­ ­ cable station for the PlusCode number that PRESS NUMBER KEY (0­9) you entered in step 3, OR (5, ), THEN (OK) PRESS (PROG. ) TO END will appear automatically on the Guide Channel Set screen. Press the Number keys (or CH +/­ or SHUTTLE PLUS %fi) to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR, then press OK. The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously. If you receive your channels through a cable box, select the cable box output channel -- the channel on which you view the cable box programs on the TV. 7 Return to normal screen Press PROG. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. · If "PROGRAM NOT COMPLETED PROGRAM OVERLAP" appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking. You can now correct the conflicting programs. See "When programs overlap each other" on page 36. 8 Engage timer recording standby mode Press TIMER. The VCR turns off automatically and "" is displayed on the front display panel. To use the VCR while it is in timer recording standby mode Press TIMER to cancel the timer recording standby mode, then press POWER to turn on the VCR. DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER after you use the VCR; otherwise, you cannot record the broadcasts you want. When "AUTO TIMER" is set to "ON" ( pg. 37, 38) , the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. [. . . ] 6 On-screen display 7 1 2 3 4 5 CH 125 RECORD FRI 12:00:00 AM PAUSE 11/30/01 ­ WARNING­ SP STEREO TIMER RECORDING SAP TO START SOON (CANCEL) B-----+-----+-----+-----E NORM HI­FI REMAIN COUNT INDEX 1 10:00 ­1:23:45 8 9 0 !@ # $ 6 1 Channel and auxiliary input ("L-1" and "F-1") 2 Day and clock time 3 Month/Day/Year 4 STEREO program indication : pg. 21 5 SAP (Second Audio Program) indication : pg. 34 8 VCR operation mode indication 9 Tape speed indication 0 Cassette indication ! [. . . ]