User manual JVC THS11EE-TH-S11 Instruction Manual

[. . . ] DVD DIGITAL THEATER SYSTEM SYSTÈME CINÉMA NUMÉRIQUE DVD TH-S11 Consists of XV-THS11, SP-WS11, SP-THS11F, SP-THS11C and SP-THS11S Se compose de XV-THS11, SP-WS11, SP-THS11F, SP-THS11C et SP-THS11S INSTRUCTIONS MANUEL D'INSTRUCTIONS GVT0155-014B [C] Français English Warnings, Cautions and Others /Mises en garde, précautions et indications diverses CAUTION ATTENTION Afin d'éviter tout risque d'électrocution, d'incendie, etc. : 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l'appareil. Ne pas exposer l'appareil à la pluie ni à l'humidité. To reduce the risk of electrical shocks, fire, etc. : 1. Do not remove screws, covers or cabinet. [. . . ] *3 You can select these modes by pressing SURROUND. (See page 19. ) Continued on next page 18 English Advanced operations English 7 All Channel Stereo All Channel Stereo (ALL ST) mode can reproduce a larger stereo sound field using all the connected (and activated) speakers. All Channel Stereo can be used while reproducing 2 channel stereo source. Normal stereo sound All Channel Stereo See page 18 for button locations. 7 When playing back 2 channel source You can select either mode of Dolby Pro Logic II (MOVIE/ MUSIC) or the DSP (ALL ST) mode. Press SURROUND repeatedly to select the desired mode. The surround mode is turned on and the current surround mode appears on the display window. Each time you press the button, the surround mode changes. To turn off the surround mode 7 Indicators on the display window Digital signal format indicators LPCM, SURR: Lights when Linear PCM signal comes in. GD, SURR: Lights when Dolby Digital signals come in. C, SURR: Lights when DTS Digital (Surround) signals come in. No indication: No digital signal indicator lights when analog signals come in. Dolby Surround mode indicators GPLII: Lights when Dolby Pro Logic II mode is activated. a: Lights when the front left channel signal comes in. b: Lights when the center channel signal comes in. c: Lights when the front right channel signal comes in. d: Lights when the LFE channel signal comes in. g: Lights when the surround left channel signal comes in. i: Lights when the surround right channel signal comes in. h: Lights when the monaural surround channel signal or 2 channel Dolby Surround signal comes in. The channel with " " shows that the corresponding speakers are reproducing the channels' sound. If the channels' sound decoded into 5. 1 channel is reproduced, only " " lights. Press SURROUND repeatedly until "SURR OFF" appears on the display window. Storing adjustments -- auto memory When you turn the power off, the system memorizes the current surround mode. The memorized mode is automatically recalled when you turn the power on. Using the on-screen bar You can check disc information and you can use some functions using the on-screen bar. Showing the on-screen bar 7 Whenever a disc is loaded Press ON SCREEN. Each time you press the button, the onscreen bar changes as follows on the TV screen. Example: During DVD VIDEO playback Selecting the surround mode The system is set up to automatically select the optimal surround mode for input signal from digital multichannel software. When playing back 2 channel source, you can select the desired surround mode manually. NOTE · This function also takes effect for the sources other than DVD. [. . . ] · DO NOT wipe it with a hard cloth. · DO NOT wipe it with thinner or benzine. · DO NOT apply any volatile substance such as insecticides to it. · DO NOT allow any rubber or plastic to remain in contact with it for a long time. Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION Power does not come on. The power cord is not connected. Connect the power cord correctly. [. . . ]