User manual JVC TK-C676

[. . . ] DOME TYPE CAMERA TK-C655 TK-C676 INSTRUCTIONS TK-C655 Ver. (C) TK-C676 Ver. (B) LWT0200-001C These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. IMPORTANT SAFEGUARDS 1. All warnings on the product and in the operating instructions should be adhered to. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. [. . . ] PATROL KEY" OFF MEMO This function is only available for the product with model name RM-P2580(A) as on the serial number plate. RM-P2580 without (A) will not function properly. RETURN TIME For setting the time to activate AUTO RETURN. Setting values :1 min, 2 min, 3 min, 5 min, 10 min, 20 min, 30 min, 60 min 1min MEMO When "AUTO RETURN" is set to "OFF", "---" will be displayed and setting will be disabled. 23 Setting Up the Camera Using an RM-P2580 CAMERA TITLE/ALARM Screen This screen sets items related to titles and alarms. Function & Setting This sets the title which is displayed permanently at the bottom left of the picture. This title can be up to 16 characters in length. 33, "CAMERA TITLE Setup" The 360° panning range can be divided into 16 areas and a title, of up to 16character in length, can be set for each area. As the camera is panned manually these area titles are displayed. This function determines whether area titles are displayed or not. 34, "AREA TITLE Setup" Sets the size of the characters in the alarm title. (Displayed when an alarm is activated. ) NORMAL : Same size as the characters used in the menu screen. DOUBLE : Double the size, both horizontally and vertically, of the characters used in the menu screen. Setting values: WHITE, GREEN, YELLOW, CYAN Sets the alarm titles. 35, "ALARM TITLE Setup" Sets the configuration of the alarm input terminals on the Ceiling Mount. The picture can be turned black-and-white mode when an alarm signal is input. 27, Item "B&W" Initial Value ­ AREA TITLE OFF AREA TITLE EDIT . . ALARM INPUT . . WHITE ­ ­ MEMO When the item "B&W" is set to ALARM 1 to 4, [B&W] will be displayed at the corresponding ALARM IN 1 to 4 items and the setting cannot be varied. ALARM IN1 Sets the camera position for alarm 1. When an alarm signal is input to the Alarm 1 input terminal, the camera moves to this set position. HOME means the home position and POS1 means position 1. Setting values: OFF, HOME, POS1 to POS99. When an alarm signal is input to the Alarm 2 input terminal, the camera moves to this set position. HOME means the home position and POS1 means position 1. Setting values: OFF, HOME, POS1 to POS99. [. . . ] · Attach so that the lock screw of the Ceiling Mount is positioned below the anchor bolt mount hole of the Ceiling Flush Mount Bracket. Hook 7. Ceiling panel Attach the camera to the Ceiling Mount. P. 18, "Attaching the Camera" 8. Attach the ceiling panel. Attach the ceiling panel, provided with the Ceiling Flush Mount Bracket, by attaching the two hooks one by one. MEMO Both the ceiling flush mount bracket and the drop prevention attachment should be insulated from the ceiling structure. If the ceiling structure is made of a metallic material, an improper insulation with the camera may produce noise in the video. 43 Others Removing a Ceiling Flush Mount Bracket (Optional WB-S575) 3. <Check the release labels thoroughly before removal. > 1. Remove the ceiling panel. Pull the ceiling panel and disengage the two hooks. 2. Clamping bracket Remove the camera. Remove the camera from the Ceiling Mount by reversing the attaching procedure. 18, "Attaching the Camera" 4. Stoppers 3. Loosen the clamping screws of the Ceiling Flush Mount Bracket. · Loosen the three clamping screws (by turning them counterclockwise). [. . . ]