User manual JVC TU-HD500A

[. . . ] Leave the 15 cm space(minimum) around the AC adapter. The rating information and safety caution of the AC adapter are on its case. LEADS Ensure the power supply lead, and all other leads, are positioned so they are not likely to be walked on or pinched by things placed on or against them. Pay particular attention to the power lead, where it enters the mains plug and where it comes out of the STB. [. . . ] You can change the day by pressing [BLUE] or [YELLOW] keys. Pressing [YELLOW] will display events of the next day. Pressing [BLUE] will display the events of the previous day. - 11 - WIDESCREEN TV sets are available with screens of the standard (4:3) format and widescreen (16:9) format. When you first installed your receiver you specified the format of the connected TV (this can now be altered i f n e c e s s a r y ; s e e S e c t i o n 3 - A D VA N C E D OPERATION - Configuring Your Receiver). Digital terrestrial television broadcasts are also made in both standard and widescreen formats. In particular, films and dramas tend to be broadcast in widescreen format to closer emulate the cinema experience, but even some news bulletins are widescreen. To help get the most from both TV set and programme when a widescreen film is watched on a standard TV, or a standard broadcast is viewed on a widescreen set, the receiver includes the [WIDE] key. So long as the receiver has been correctly set up for the TV set connected, a widescreen programme will always be displayed correctly on a widescreen set, and a standard format programme will correctly fill the screen of a standard format TV. With a standard format TV displaying a widescreen programme, the [WIDE] key switches between displaying the picture with black bars at the top and bottom of the screen, and filling the whole height of the screen but cropping the sides off according to instructions broadcast with the programme (called 'pan and scan'). The effect of the [WIDE] key on the picture display is cancelled by pressing [WIDE] again, changing channel or turning the receiver to standby. Subtitle With Digital terrestrial broadcasting, some programmes are broadcast with subtitles. TV TYPE Digital terrestrial television channels can broadcast programmes in a widescreen format which must be output differently to normal and widescreen TV sets. This function tells the receiver the screen format of the TV connected so that broadcasts are displayed correctly. Highlight the TV Type line in the Configuration menu and use the [LEFT] or [RIGHT] keys to select 4:3 if you have a standard TV set connected or 16:9 if it is a widescreen TV. This function duplicates the selection made at the time of first installation (see 1 - PREPARATION - Tuning In) and can be used if you change TV sets. Return to normal TV viewing by pressing the [MENU] key. TV OUT The receiver can output either an RGB/Y/C, Video signal from the TV SCART on the rear panel. Although the RGB format results in a better quality picture, not all equipment - particularly some VCRs - can cope with an RGB signal (see Appendix C Connecting A VCR). Enter PIN code: Use UP / DOWN buttons to go to Enter PIN code option. Use NUMBER buttons to enter new password. New Password is asked twice for confirmation. ANTENNA POWER SUPPLY Use UP/DOWN buttons to go to Antenna Power Supply Setting. If you want connect the receiver to an active antenna that is an instrument amplifying the received signal then you must change the Antenna Power Supply setting to ON. The DVB-T receiver can supply 5V DC at 30mAmp maximum. [. . . ] Press the [MENU] key to display the Main Menu and using the [UP] or [DOWN] keys, highlight the Installation line and press [OK] to display the Installation Menu. You can either perform a First Time Installation, effectively resetting the receiver to its factory setting condition, or just search for channels. If, alternatively, from the search options menu the Manual Search line is highlighted and [OK] pressed, the manual search screen is displayed. Highlight the YES button with the [LEFT] or [RIGHT] key and press [OK] to start the automatic search. FIRST TIME INSTALLATION To reset the receiver, highlight the First Time Installation line in the menu and press [OK]. A warning screen is displayed in case of accidental operation. This is for searching for digital channels on a single broadcast frequency. [. . . ]