User manual JVC UX-5000

[. . . ] ULTRA MICRO COMPONENT SYSTEM ULTRA-MIKRO-KOMPONENTEN-SYSTEM SYSTEME DE COMPOSANTS ULTRA MICRO ULTRA MIKRO KOMPONENTENSYSTEEM SISTEMAS DE COMPONENTES ULTRA MICRO SISTEMA AD ULTRA MICROCOMPONENTI UX-5000 AHB. SUPER PRO PRESET TUNING DOWN MULTI CONTROL UP CLOCK SLEEP REMOTE CONTROL RM-RXU5000 OPEN/CLOSE AUX MD/TAPE TUNER BAND CD DIMMER SLEEP TIMER/SNOOZE DISPLAY FM MODE AHB. AUTO SUPER PRO PRESET AUX CD PROGRAM RANDOM REPEAT BASS TREBLE CANCEL UP SET DOWN VOLUME STANDBY MD /TAPE TUNER BAND CD VOLUME ULTRA MICRO COMPONENT SYSTEM UX-5000 PHONES INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. [. . . ] s Select a station using one of the following methods. or DOWN SET s s s Manual Tuning Press the 4 or ¢ button on the Unit or the Remote Control repeatedly to move from frequency to frequency until you find the station you want. OR Auto Tuning If you press and hold the 4 or ¢ button on the Unit or the Remote Control for one second or more, the frequency changes down, or up, automatically until a station is found. OR Preset Tuning using the Remote Control (Possible only after presetting stations) When changing the Band FM = 30, AM = 15 1. s Select a band by pressing the TUNER BAND button. s Press the 4 or ¢ button to tune in a sta3. s Press the SET button. "P------" is displayed. The lower 2 digits blink. 8 select the preset number. UP button: Increases the preset number by 1. DOWN button: Decreases the preset number by 1. > button: Increases the preset number by ten. < button: Decreases the preset number by ten. 5. s Press the SET button. After 1 second, the display returns to the broadcast frequency display. 6. s Repeat above steps 1 to 5 for each station you want to store in memory with a preset number. To cancel during presetting, press the CANCEL button in step 3 or 4. To change the preset stations, repeat the same steps as above. Auto Presetting In each band, you can automatically preset FM-30, AM (MW/LW)15 stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up the frequency. TUNER BAND AUTO PRESET (for 2 seconds) 1. s Select a band by pressing the TUNER BAND button. s Press the AUTO PRESET button on the 3. s Repeat steps 1-2 for the other band. Remote Control for more than two seconds. s If you want to change the preset stations, carry out the Manual Presetting for the desired preset numbers. CAUTION: If the System is unplugged or if a power failure occurs, the preset stations will be erased after about 24 hours. If this happens, you will need to preset the stations again. To Change the FM Reception Mode When you are tuned into an FM stereo broadcast, the "ST (Stereo)" indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose any stereo effect. Press the FM MODE button on the Remote Control so that the "MONO" indicator lights up on the display. FM MODE ST(Stereo) MONO To restore the stereo effect, press the FM MODE button on the Remote Control so that the "MONO" indicator goes off. 9 English 4. s Press the UP, DOWN, >, or < button to English s Using the CD Player s REMOTE CONTROL RM-RXU5000 DIMMER SLEEP DISPLAY FM MODE AHB. [. . . ] Do not touch the shiny surface of the CD, or bend the CD. Put the CD back in its case after use to prevent warping. Be careful not to scratch the surface of the CD when placing it back in the case. Avoid exposure to direct sunlight, temperature extremes, and moisture. [. . . ]