User manual JVC UX-G30,UX-G33

[. . . ] MICRO COMPONENT SYSTEM UX-G33--Consists of CA-UXG33 and SP-UXG33 UX-G30--Consists of CA-UXG30 and SP-UXG30 INSTRUCTIONS GVT0171-001B [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] Changes the source to AUX automatically. (If you change from AUX to another source, QP Link will be canceled. ) · While the System is on standby. . . Turns on the System and activates the AUX source automatically (except when the display is turned off). S. TURBO To locate a track directly · For regular CDs NUMBER SELECT Remote ONLY 1 Activate the track number entry mode. S. TURBO QP Link · For MP3 discs MP3 S. TURBO QP Link QP Link Bubbles appear when QP Link works. 2 Enter a track number you want to play back. PRESET/GROUP/PTY UP DOWN While QP Link plays back the device. . . SET S. TURBO QP Link Increases the numbers. Decreases the numbers. Bubbles disappear when the sound signal stops or is too weak. 9 Daily Operations--Sound&Other Adjustments To drop the volume in a moment Remote control FADE MUTING Remote ONLY SLEEP A. STANDBY CLOCK/ TIMER DIMMER SET CANCEL To restore the volume, press again, or adjust the volume level. Adjusting the Sound To emphasize the sound--Sound Turbo This function emphasizes the sound. DISPLAY MODE SOUND TURBO FADE MUTING PRESET/GROUP/PTY DOWN, UP AHB PRO BASS/ TREBLE VOLUME SOUND TURBO TURBO ON (Initial setting) (Canceled) TURBOOFF To reinforce the bass sound --AHB Pro Remote ONLY You can reinforce the bass sound to maintain rich, full bass at low volume--Active Hyper Bass Pro. AHB PRO AHB ON AHB OFF (Canceled) Main unit DIMMER SOUND TURBO VOLUME ­/+ · You can activate AHB Pro only while Sound Turbo is canceled. To adjust the tone--Bass/Treble To adjust the bass BASS/ TREBLE Remote ONLY DOWN 4 ¢ UP You can adjust the bass and treble level from ­3 to +3. VOLUME BASS TRE Canceled Adjusting the Volume The volume level can be adjusted between "VOL MIN" and "VOLUME 1" ­ "VOLUME 40 (VOL MAX). " Remote control: VOLUME To adjust the treble BASS/ TREBLE VOLUME Main unit: VOLUME BASS TRE Canceled 10 Changing the Display Brightness You can dim the display window. DIMMER 2 Adjust the hour, then the minute. PRESET/GROUP/PTY UP DOWN SET DIM 1 DIM 2 Now the built-in clock starts working. To check the current time during play DISPLAY MODE (Initial setting) DIM OFF DIM 1 DIM 2 Dims the display and the illumination on the main unit. Dims the display more than DIM 1 and turns off the illumination on the main unit. Clock ( PS PTY RT )* Source information * Only while FM is selected as a source (see page 12) Adjusting the Audio Input Level Remote ONLY If the sound from a component connected to the AUX jack is too loud or is too quiet, you can change the audio input level through the AUX jack (without changing the volume level). While AUX is selected as a source. . . 2 sec. SET Turning Off the Power Automatically Remote ONLY Auto Standby 2 sec. A. STANDBY AUX LVL1 AUX LVL2 On Canceled AUX LVL3 (Initial setting) AUX LVL 1 AUX LVL 2 AUX LVL 3 Select this when the sound is too loud. AUX Level 2 is preset at the intermediate level between Level 1 and 3. Select this when the sound is too quiet. Setting the Clock Remote ONLY When Auto Standby is in use, the A. STBY indicator lights on the display. The A. STBY indicator starts flashing: · When disc playback stops · When the sound signal from the AUX jack stops or is too weak The System will turn off (on standby) automatically if no operation is done for about 3 minutes while the indicator is flashing. Without setting the built-in clock, you cannot use Daily Timers (see page 16) and Sleep Timer. · To exit from the clock setting, press CLOCK as required. · To go back a step, press CANCEL. Sleep Timer You can set the unit to turn off after a certain period of time. 1 Specify the time (in minutes). SLEEP 1 Activate the clock setting mode. CLOCK/ TIMER S. TURBO QP Link 10 20 30 60 90 Canceled 120 150 2 Wait until the set time disappears. To check the time remaining until the shut-off time SLEEP S. TURBO QP Link SLEEP · If you have already adjusted the clock before, press the button repeatedly until the clock setting mode is selected. · If you press the button repeatedly, you can change the shutoff time. 11 Advanced Radio Operations Remote control Searching for a Program by PTY Codes Remote ONLY You can locate a particular kind of program from the preset channels (see page 8) by specifying the PTY codes. To search for a program using the PTY codes PTY SEARCH 7 PRESET/GROUP/PTY DOWN, UP REPEAT/ TA/News/Info FM S. TURBO ST 1 While listening to an FM station. . . PTY SEARCH S. TURBO QP Link FM ST DISPLAY MODE Receiving FM Stations with Radio Data System Remote ONLY QP Link Radio Data System allows FM stations to send an additional signal along with their regular program signals. This System can receive the following types of Radio Data System signals. PS (Program Service) PTY (Program Type) RT (Radio Text) Enhanced Other Networks Shows commonly known station names. Provides the information about the types of the programs broadcast by the Radio Data System stations of the different networks. 2 Select a PTY code. PRESET/GROUP/PTY UP DOWN · For details about each PTY code, see page 13. 3 Start searching. PTY SEARCH S. TURBO QP Link FM ST FM S. TURBO QP Link ST Ex. When "NEWS" is selected To show the Radio Data System information While listening to an FM station. . . DISPLAY MODE Clock PS PTY RT Frequency (Non Radio Data System signal) The receiver searches 30 preset FM stations, stops when it finds the one you have selected, and tunes in to that station. · If no program is found, "NOTFOUND" appears on the display. · To stop searching any time during search, press PTY SEARCH. To continue searching after it stops on an unwanted station While the indications on the display are flashing. . . PTY SEARCH PS PTY RT Station names are displayed. [. . . ] ] There are two types of ID3 Tag--Version 1 and Version 2. This System can only show ID3 Tag Version 1. MP3 groups and tracks are not played back as you expect. ] The playing order is determined when the disc was recorded. [. . . ]