User manual JVC UX-H100UJ

[. . . ] MICRO COMPONENT SYSTEM UX-H100 --Consists of CA-UXH100 and SP-UXH100 INSTRUCTIONS LVT1190-010A [UJ] Warnings, Cautions and Others CAUTION-- STANDBY/ON button ! Disconnect the mains plug to shut the power off completely (all lamps and indications go off). The STANDBY/ON button in any position does not disconnect the mains line. · When the unit is on standby, the STANDBY lamp lights red. · When the unit is turned on, the STANDBY lamp goes off. [. . . ] In stereo mode, you can hear stereo sound when a stereo program is broadcast. · Changing the station also cancels the MONO mode. 10 Listening to FM and AM Broadcasts (continued) Presetting Stations You can preset 30 FM and 15 AM stations manually. In some cases, test frequencies have been already stored for the tuner since the factory examined the tuner preset function before shipment. You can preset the stations you want into memory by following the presetting method. · There is a time limit in doing the following steps. If the setting is canceled before you finish, start again from step 2. Tuning in to a Preset Station On the remote control ONLY: 1 Press FM/AM to select either "FM" or "AM. " FM/AM The unit automatically turns on and tunes in to the previously received station--either FM or AM. · Each time you press the button, the band alternates between FM and AM. 2 Press PRESET UP or PRESET DOWN repeatedly to select a preset number. PRESET UP On the remote control ONLY: 1 Tune in to the station you want to preset. · See "Tuning in to a Station" on page 10. PRESET DOWN 2 Press PLAY MODE. The preset number starts flashing on the display. · The PRGM (program) indicator lights up on the display. PRGM PLAY MODE To tune in to a preset station directly using the number buttons On the remote control ONLY: Pressing the number button(s) allows you to select the preset number you want. 1 3 2 Ex. : For preset number 5, press 5. For preset number 15, press +10, then 4 6 5 5. 7 9 8 For preset number 20, press +10, then 10. 10 +10 For preset number 30, press +10, +10, then 10. 3 Press ¢ or 4 to select a preset number. PRGM You can also use the number button(s) to select a preset number. For preset number 15, press +10, then 5. For preset number 20, press +10, then 10. For preset number 30, press +10, +10, then 10. 1 4 7 10 2 5 8 +10 3 6 9 4 Press PLAY MODE again. PLAY MODE 5 To preset more stations, repeat steps 1 to 4 above, allocating a different preset number to each station. · Storing a new station on an already assigned number erases the previously stored one. When you unplug the AC power cord or if a power failure occurs The preset stations will remain in the unit. 11 Playing Back Discs This unit has been designed to play back the following discs--CD, CD-R, and CD-RW. You can play back the discs containing the tracks in music CD format or MP3 files in ISO 9660 format. · In this instruction, we call a disc recorded MP3 files "MP3 disc, " and "file" is also referred to as "track. " Continued 2 Place a disc correctly with its label side up, then press down on the portions around the disc's center hole until you hear a click. When playing CD-Rs or CD-RWs · Before playing CD-Rs or CD-RWs, read their instructions or cautions carefully. · User-edited CD-Rs (CD-Recordable) and CD-RWs (CDReWritable) can be played only if they are already "finalized. " · This unit supports "multi-session" discs (up to 5 sessions). · This unit cannot play "packet write" discs. · Some CD-Rs or CD-RWs may not play on this unit because of their disc characteristics, damage or stain on them, or if the player's lens is dirty. · CD-RWs may require a longer readout time. This is because the reflectance of CD-RWs is lower than for regular discs. 3 Close the disc cover gently. [. . . ] · Put the disc back in its case after use to prevent warping. · Be careful not to scratch the surface of the disc when placing it back in its case. · Avoid exposure to direct sunlight, temperature extremes, and moisture. Head To clean the disc Wipe the disc with a soft cloth in a straight line from center to edge. Pinch Roller To demagnetize the head Turn off the unit, and use a head demagnetizer (available at electronic and audio shops). DO NOT use any solvent--such as conventional record cleaner, spray, thinner, or benzine--to clean the disc. 21 Troubleshooting If you are having a problem with your unit, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person, such as your dealer, for service. Symptom Power does not come on. No sound is heard. Possible Cause The power cord is not connected to an AC outlet. [. . . ]