User manual JVC UX-Z7MDR

[. . . ] MICRO COMPONENT MD SYSTEM UX-Z7MDR--Consists of CA-UXZ7MDR and SP-UXZ7MD TA/News/Info INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0900-003A [B] Warnings, Cautions and Others IMPORTANT for the U. K. [. . . ] · Each time you press the button, the reverse mode changes as follows: : Plays back only one side (front or reverse). : Plays back the front and reverse sides once. : Plays back both front and reverse sides continuously. Cassette holder To change the information shown in the main display On the remote control ONLY: Each time you press DISP/CHARA, the information in the main display alternates between the source indication and the clock indication. · If an MD is inserted, the MD remaining recording time ("REC REMAIN") is shown before the clock indication. 3 Push ) (PUSH OPEN) gently to close the cassette holder. 4 Press TAPE 2 3. The unit automatically turns on and the tape play starts from the front side. · Each time you press the button, the tape direction changes as follows: : Plays the front side (left to right). : Plays the reverse side (right to left). TAPE indicator Reverse mode and tape direction indicators · The use of the C-120 or thinner tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinch rollers and the capstans. · You can also play back type II and type IV tapes, however, the sound quality (tone) may not be reproduced properly. Tape direction (left to right) When the tape plays to the end, the deck automatically or . (See stops if the reverse mode is set to "To play both sides--Reverse mode" in the right column. ) ­ 33 ­ Listening to External Equipment The buttons emphasized in the illustration below are used and explained in this section (page 35). Remote control TA/News/Info Main unit ­ 34 ­ Listening to External Equipment You can listen to external equipment connected to the AUX/DVD jacks on the rear of the unit. · First make sure that the external equipment is properly connected as follows: DO NOT connect other equipment while the power is on. Right External equipment Left 4 Adjust the volume level of the unit to your desired listening level. 5 Apply sound effects, if you wish. · For how to apply sound effects, see page 14. Adjusting the Audio Input Level If the sound from the component connected to the AUX/DVD jacks is too loud or is not loud enough when changing from another source to "AUX" (without changing the volume level), you can change the audio input level through the AUX/DVD jacks. R 1 Press FM/AM/AUX (or AUX/DVD on the main unit) repeatedly so that "AUX" appears in the main display. On the remote control: · Each time you press the button, the source changes as follows: L To AUX/DVD jacks FM AUX AM 2 Press and hold SET on the remote control for more SPEAKERS R L CAUTION: R L SPEAKER IMPEDANCE 4~16 1 Press FM/AM/AUX (or AUX/DVD on the main unit) repeatedly so that "AUX" appears in the main display. On the remote control: · Each time you press the button, the source changes as follows: than 2 seconds. · Each time you press and hold the button, the audio input level alternates between "LEVEL 1" and "LEVEL 2. " "LEVEL 1": Select this when the sound is too loud (initial setting). "LEVEL 2": Select this when the sound is not loud enough. FM AUX AM To change the information shown in the main display On the remote control ONLY: Each time you press DISP/CHARA, the information in the main display alternates between the source indication and the clock indication. · If an MD is inserted, the MD remaining recording time ("REC REMAIN") is shown before the clock indication. 2 Adjust the volume level of the unit to "VOLUME 0. " 3 Start playing the external equipment. · For operation of the external equipment, see the manuals supplied with it. ­ 35 ­ Recording The buttons emphasized in the illustration below are used and explained in this section (pages 37 to 43). For recording operations, you mainly use the buttons on the main unit. Main unit Remote control TA/News/Info ­ 36 ­ Before You Start Recording on an MD · It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic embodied therein. · When you record onto partially recorded MD, its contents are not erased or overwritten. The recording starts from the point following the last recorded track of the MD. If you want to record on such an MD from the beginning, you have to erase its contents first (see "Erasing All Tracks --ALL ERASE" on page 58). · When an MD is fully recorded, recording will stops automatically. · The recording level is automatically set correctly, so it is not affected by the volume level. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level. [. . . ] (See pages 6 ­ 9. ) · A pair of headphones is connected. · Unplug the headphones from the PHONES jack. · You are using a prerecorded MD. · Change it with a recordable MD. [. . . ]