User manual JVC VN-C205 (READ ME FIRST)

[. . . ] FIXED DOME NETWORK CAMERA VN-C205 READ ME FIRST For Customer Use: Enter below the Serial No. Retain this information for future reference. VN-C205 LWT0281-001A-H Safety Precautions FOR USA AND CANADA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Due to design modifications, data given in this instruction book are subject to possible change without prior notice. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] ( Page 24) ¤ & < Video setting switch * [D/N - ON/OFF] Easy Day & Night switch To capture a subject with continually changing brightness (day/night), set this switch to "ON". The camera automatically captures the image in color when the subject is bright, and in black and white mode when it is dark. (Default setting: OFF) > fi Caution The Easy Day & Night feature on this camera uses a sensitized black and white mode unlike other black and white surveillance cameras that use infra-red lighting. ( [FOCUS ADJ. - ON/OFF] focus adjustment switch When adjusting the focus during installation, setting this switch to "ON" will open the iris. (Default setting: OFF) ( page 24) 11 Preparation Connection Examples LAN Connection VN-C205 LAN VN-C205 PC Internet Connection VN-C205 VN-C205 LAN INTERNET FTP Server PC Updated images are automatically uploaded at a regular interval PC Peer-to-Peer Connection VN-C205 Crossover Cable PC 12 Preparation Procedure Set the camera in the following procedure. Step 1 Connection/Installation Firstly, make a hole in the ceiling, followed by connecting the input power cable, LAN cable or alarm signal cable to the terminal of this camera. Do not forget to attach the safety wire. Page 14 Step 2 Network Settings Install the software, set the network for this camera as well as using the "VNC205U Setup Tool", and register the connected camera with the "V. Networks Controller". Page 27 In a system where more than 1 VN-C205 is used, turn on the power for a VN-C205 first, followed by setting the camera until "2-3 Setting IP Address for this Camera Using the 'VN-C205U Setup Tool' " is completed. Upon doing so, turn on a second camera and perform setting in the same way. Perform the same procedure for subsequent cameras. (Page 22) Step 3 Setting Using the V. Networks Controller Perform settings for Image Quality and Alarm using the "V. Networks Controller" software that has been installed. Page 34 Step 4 Operating Using the V. Networks Controller The "V. Networks Controller" can also be used to perform recording/playback operations. For details, refer to the PDF instruction manual inside the supplied CD-ROM. Step 5 Operating Using a Web Browser Operation is possible via a web browser. Page 36 13 Preparation (Step 1 Connection/Installation) 1-1 The flowchart of installation work for camera Getting Started Caution Attachment of a embedded cover in the ceiling (recess bracket) may be mandatory in certain regions. If this is so, ensure that the embedded cover (recess bracket) is securely attached before installing the camera. ( Page16) 1. Preparation Mount to the ceiling ( Page 16) Open a hole on the ceiling ( Page 16) Mount the electric box to the ceiling ( Page 25) Open a hole on the ceiling ( Page 25) Mount to the electric box ( Page 25) Pull out the cables from the ceiling ( Page 16) Attach the safety wire to the camera unit ( Page 16) Remove the dome cover ( Page 17) Do the wiring at the end of the alarm cable ( Page 17) Insert the CF card ( Page 17) Pass the supplied cable under the plate for depressing cables. ( Page 26) Pull out the cables aside and mount ( Page 26) 14 2. Installation Mount to the ceiling ( Page 16) Mount the electric box to the ceiling ( Page 25) Pull out the cables aside and mount ( Page 26) Mount the safety wire to place which is firm such as ceiling ( Page 20) Connect the video signal cable ( Page 20) Connect the LAN cable ( Page 20) Connect the alarm signal cable ( Page 20) Connect the input power cable ( Page 20) Wind the cables with tape ( Page 21) Bundle the cables and pass them through the wire clamp ( Page 26) Face the camera towards the direction for shooting ( Page 21) Mount the camera to the ceiling ( Page 21) Mount the camera to the electric box ( Page 25) Mount the camera to the ceiling ( Page 21) 3. Adjustment of the camera's angle of view Connect to the monitor ( Page 23) Adjust the lens and camera angle ( Page 23) Mount the dome cover ( Page 24) 15 Preparation (Step 1 Connection/Installation) 1-2 Mounting the Camera to the Ceiling Cautions Attachment of a embedded cover in the ceiling (recess bracket) may be mandatory in certain regions. If this is so, ensure that the embedded cover (recess bracket) is securely attached before installing the camera. Please refer to the instruction manual for the cover in use for details on installation of the embedded cover (recess bracket). For more detail, please contact the JVC. Ceiling Embedded Cover in Ceiling (recess bracket) 1. Preparations Open hole in ceiling, connect cables and mount camera to ceiling. 1. Input power cable LAN cable Video signal cable 1. Open a hole in the ceiling. 20 mm (3/4 inches) Use the template and open a hole in the ceiling for the cables. Note Approx. 100 mm (3-7/8 inches) 2. Alarm signal cable There is no need to open a hole in the ceiling when using the cable extraction hole on the side of the camera. Pull out the cables from the ceiling. Before connecting, pull out the input power cable and video signal cables about 100mm (3-7/8 inches) from the ceiling. Safety cable 3. 3. [. . . ] Description in this manual is based on the web page browsing/display screen of Internet Explorer. Password Upon changing a password, the password confirmation screen may appear, which requires you to enter the new password twice. When this screen appears, enter the same password twice. 36 5-2 Access Authorization Level The configuration of URLs (web pages) in VN-C205 is illustrated as follows. Access Authorization Level << User >> << Operator Top page Still image page (index-e. html) (still-e. html) >> << Administrator >> Live image page (java-e. html) Still image URL (still. jpg) Settings ( java config-e. [. . . ]