User manual JVC VS-5313 mkII service manual

[. . . ] If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. If nontheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below: IMPORTANT FOR LASER PRODUCTS REPRODUCTION OF LABELS 1 CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE CLASS LASER 1 PRODUCT 2 WARNING LABEL, PLACED INSIDE THE UNIT CAUTION: Invisible laser ADVARSEL: Usynlig laserradiation when open and stråling ved åbning, når interlock failedor defeated. [. . . ] I Some power is always consumed even though power is turned off (called Standby Mode). I To switch off the System completely, unplug the AC power cord from the wall outlet. When you unplug the AC power cord, the clock will be reset to 0:00 after about 20 minutes. Power Save Mode You can reduce the power consumption in standby mode. Press the DISPLAY button on the Remote Control when the System is turned off. · The clock display goes out. When the System is Turned On Each time you press the DIMMER button on the Remote Control, the brightness of the backlighting and the illumination on the cover change as follows: Display DIMMER OFF DIMMER 1 DIMMER 2 Backlighting Bright Slightly Dark Dark Illumination Bright Slightly Dark Off · When the System is turned off once, then turned on again, the brightness setting will be restored to the previous one since the setting is stored in memory. 12 Basic Operations Changing the Color (COLOR) (VS-DT9R only) (Using the Remote Control) You can change the color of the illumination on the Unit. Adjusting the Volume To increase the volume, press the VOLUME + button on the Remote Control (or VOL + button on the Unit). To decrease the volume, press the VOLUME ­ button on the Remote Control (or VOL ­ button on the Unit). 1 2 Press the % button to turn on the System. Press the COLOR button on the Remote Control. "RANDOM COLOR" is displayed. You can adjust the volume level between 0 and 50. CAUTION: · DO NOT turn off the System with the volume set to an extremely high level; otherwise a sudden blast of sound could damage your hearing, speakers and/or headphones when you turn on the System or start playing any source next time. REMEMBER you cannot adjust the volume level while the System is in standby mode. 3 Press the or button to select the setting of your choice. The color changes as follows: (Blue) (Red) RANDOM COLOR: B | R: (Blue) (Red) GRADATION: The color changes randomly. The color between blue and red is selectable in 16 steps using the > or < button. The color changes gradually between blue and red. For private listening Connect a pair of headphones to the PHONES jack. Its band and frequency are displayed. · In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best reception. (on the Unit) 15 Using the Tuner Presetting Stations (Using the Remote Control) You can preset up to 30 FM stations and up to 15 AM (MW/ LW) stations. CAUTION: · Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again. · Preset numbers may have been set to factory test frequencies prior to shipment. You can preset the stations you want into memory by following one of the presetting methods below. Manual Presetting SET FM/AM STORED SET SET or When changing the Band FM = 30, AM = 15 1 2 3 Select a band by pressing the FM/AM button. Press the 4 or ¢ ( tune in a station. Press the SET button. "SET" will blink for 5 seconds. Within 5 seconds, proceed to the next step. When the display returns to the one set in step 2 after 5 seconds, press the SET button again. or ) button to 4 Press the > or < button within 5 seconds to select the preset number. > or < button: Increase or decrease the preset number by 1. Pressing and holding the button will rapidly increase or decrease the preset number. 5 6 Press the SET button within 5 seconds. "STORED" appears and after 2 seconds, the display returns to the broadcast frequency display. Repeat above steps 1 to 5 for each station you want to store in memory with a preset number. To change the preset stations, repeat the same steps as above. 16 Using the Tuner To Change the FM Reception Mode (Using the Remote Control) When you are tuned into an FM stereo broadcast, the "STEREO" indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect. Press the FM MODE button on the Remote Control so that the "MONO" indicator lights up on the display. FM MODE To show the RDS signals on the display Press the DISPLAY MODE button while listening to an FM station. [. . . ] - DO NOT wipe it with thinner or benzine. - DO NOT apply any volatile substance such as insecticides to it. - DO NOT allow any rubber or plastic to remain in contact with it for a long time. CAUTION: · Do not use any solvent (for example, conventional record cleaner, spray thinner, benzine, etc. ) to clean a CD. Moisture Condensation Moisture may condense on the lens inside the System in the following cases: · After turning on heating in the room. · If the System is brought directly from a cold to a warm place. [. . . ]