User manual JVC XL-R5000

[. . . ] CD/CDR MULTIPLE COMPACT DISC RECORDER XL-R5000BK CD REC CD EDIT SYNCHRO DISPLAY POWER FINALIZE MENU CD 1 1 4 7 10 2 5 8 +10 3 CD 2 XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER EJECT REC LEVEL 6 CD 3 9 CONTROL CD SET REC SOURCE SELECTOR PLAY & EXCHANGE CDR CANCEL CD CONTROL 3-CD DIGITAL CD LINE MIXING MIC FINALIZE MIN MAX PLAY MODE REPEAT CDR CONTROL MIX BALANCE PHONES LEVEL PITCH + STANDBY CLOCK/ TIMER PLAY MODE CD EDIT CD REC DISPLAY MENU MULTI JOG REC MUTING SYNCHRO REC CANCEL SET POWER ­ + LINE MIC CD LINE MIN MAX MIC PHONES PITCH 0 REC PITCH ­ SHIFT REC MUTING REMOTE CONTROL RM-SXLR5000J INSTRUCTIONS For Customer Use: Enter below the Model No. which are located on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0452-001C [ J/C/B/U ] Warnings, Cautions and Others For U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] However, when automatic track marking is turned on, manual track marking cannot be operated. · DIGITAL : For recording the sound of a unit which has been connected to the OPTICAL IN connector (digital input) When you switch from DIGITAL source recording to another source, press the DIGITAL button once to turn off the indicator, and then select the other source. · CD : For recording the CDs loaded in into CD1, CD2 and/or CD3 Press CD repeatedly to select either DIGITAL or ANALOG recording. Note: Analog recording is performed for CD+LINE or CD+MIC mixing even when the CD pitch control has been set to OFF. · LINE : For recording the sound of a unit which has been connected to the LINE IN connectors (analog input) : For recording the sound from a microphone which has been connected to the MIC connector (analog input) · MIC Sampling rate converter The unit incorporates a sampling rate converter to ensure that the original digital signals will be recorded regardless of the sampling frequency (32 kHz, 44. 1 kHz or 48 kHz) of the source being recorded. Notes · If a source has already been selected, its corresponding lamp will light. · When playback is stopped and the CDR is selected, pressing the DISPLAY button displays the remaining recording time on the disc for 3 seconds. 18 English 4 When analog signals are to be recorded, adjust the recording level. REC LEVEL · REC MUTING cannot be used at the beginning of a recording from the record pause mode · Adjust the volume in such a way that the 0 dB display is not exceeded when the loudest sound is supplied. L R 40 30 20 15 10 6 3 0 dB Setting automatic or manual track marking When automatic track marking is turned on, tracks are automatically set in the recording. For digital sources, the track information recorded in the digital source signal is used. For analog recording, spaces of silence are interpreted as track separations. For analog recording, automatic track marking is performed when the unit detects 4 seconds of silence in the recording. Manual track marking offers the flexibility to place track marks anywhere in your recording. MIN MAX The OVER indicator should not be made to light as this may cause distortion in the recording. 5 Play the sound of the source to be recorded. · If the CD1 button is pressed when CD serves as the source, the tracks are recorded in the following sequence: CD1 = CD2 = CD3 To turn on automatic track marking XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER REC LEVEL 6 Press the 3 (play) button to start recording. MIN MAX MIX BALANCE PHONES LEVEL When recording is complete Press the 7 (STOP) button to stop, the 3 indicator flashes and operation stops. Note · When UNLOCK appears in the display, the OPTICAL IN connector is not connected to the source unit. · Upon completion of recording, the 3 indicator flashes. Operating any button while this indicator flashes may render the disc unusable. Always wait until the 3 indicator stops flashing before proceeding with the next operation. · When digital input signals are supplied, they will be recorded in their original digital form. There is no need to adjust their recording level. MULTI JOG STANDBY POWER ­ + CANCEL 4, 6 2 CD REC SYNCHRO DISPLAY POWER CD EDIT FINALIZE MENU 3, 5 2 1 CANCEL CD 1 1 4 7 10 2 5 8 +10 3 CD 2 6 CD 3 9 CONTROL CD SET CDR CANCEL PLAY MODE REPEAT 4, 6 2 SHIFT PITCH + To record silence in the recording PITCH 0 REC PITCH ­ XL - R5000 CD/CDR MULTIPLE COMPACT DISC RECORDER REC LEVEL 3, 5 REC MUTING REMOTE CONTROL RM-SXLR5000J MIN MAX MIX BALANCE PHONES LEVEL MULTI JOG STANDBY POWER ­ + 1 PITCH + Press CD-R on the remote control while pointing at the unit to select the CDR function. When the unit is in the stop mode, press the MENU button on the main unit (or the DISPLAY/MENU button on the remote control while holding down the SHIFT button). Turn the MULTI JOG dial or press the 4/¢ button on the remote control until "AUTO TRACK" appears in the display. 1, 2 REC REC MUTING 2 3 4 PITCH 0 1, 2 SHIFT PITCH ­ 1, 2 REMOTE CONTROL RM-SXLR5000J 1 While the CDR is recording, press the REC MUTING button on the main unit (or press REC ¶/REC MUTING while the SHIFT button is pressed down on the remote control) to start recording silence . After four seconds of silence has been recorded, the unit is put in the record pause mode. Press the SET button. · The current setting is displayed on the screen. Turn the MULTI JOG dial or press the 4/¢ button on the remote control to select "AUTO TR ON". 5 6 2 Notes · Four seconds of silence is recorded even if the button is held down for less than four seconds. Even if the button is held down for longer than four seconds, the unit is put in the record pause mode after the button is released. Press the SET button. · If "AUTO TR ON" is selected, the AUTO TRACK indicator lights in the display. [. . . ] · Insert it properly with the label side facing up. · Turn on the power and wait for a couple of hours. · Load the disc with the label side up. · Replace with a disc that can be recorded on. Ref The time display flashes in the display window. [. . . ]