User manual JVC XM-G6

[. . . ] MINIDISC RECORDER XM-G6 SAMPLING RATE CONVERTER MINIDISC RECORDER XM-G6 REC PAUSE REC INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0378-002A [B] Warnings, Cautions and Others CAUTION To reduce the risk of electrical shocks, fire, etc. : 1. [. . . ] If sound signal is too weak for this unit to detect, Sound Synchronized Recording will not start (or will stop even while the source is being played). · To stop recording temporarily, press REC PAUSE button or 6 (play/pause) button on the MD recorder or MD 6 (play/pause) button on the remote control. · To resume recording, press 6 (play/pause) button on the MD recorder or MD 6 (play/pause) button on the remote control again. Each time you press DISPLAY/CHARA. button, information switches between the remaining time for the recording and the elapsed time with the track number of the MD alternately. 6 Press 7 (stop) buttons both on the MD recorder and the cassette deck to quit recording as required. "WRITING" appears in the display window, and you can remove the MD and the tape by pressing 0 (eject) buttons. Using 7 (stop) button on the remote control, you cannot stop both the MD recorder and the cassette deck. Make sure to press each button on both units. Recording a Tape Manually 1 2 Recording a Tape -- Sound Synchronized Recording Insert a recordable MD into the MD loading slot. · Place a tape on the tape tray, press ` (playback) button on the cassette deck or TAPE ` (playback) button on the remote control, then press 7 (stop) button before going to the next step. Press REC PAUSE button on the MD recorder. The REC indicator on the MD recorder lights red, and the MD recorder switches to the recording-pause mode. Press 6 (play/pause) button on the MD recorder or MD 6 (play/pause) button on the remote control. The MD recorder starts recording, and information changes in the display window and the remaining time for recording appears as follows: Setting the recording mode, you can start playing back a tape and recording it onto an MD simultaneously. 1 2 Repeat the steps 1 and 2 in the previous section on this page. Press REC MODE button behind the sliding panel to select a recording mode as follows: 3 4 3 Press SET button. REC indicator on the MD recorder lights red, and information appears in the display window as follows: 5 Press ` (playback) button on the cassette deck or TAPE ` (playback) button on the remote control in succession. 15 Continued 4 Press ` (playback) button on the cassette deck or TAPE ` (playback) button on the remote control. Once the cassette deck starts playback, the MD recorder detects the audio signals and starts recording. Each time you press DISPLAY/CHARA. button, information switches between the remaining time for the MD and the elapsed time for the MD alternately. Synchronized recording an MD onto a tape 1 2 Insert an MD to be played-back into the loading slot, and load a recordable tape. Press 6 (play/pause) button on the MD recorder or MD 6 (play/pause) button on the remote control, then press 7 (stop) button immediately to prepare playing back the MD. Press REC MODE button behind the sliding panel to select "SYNC REC>TAPE. " · If no sound comes in for more than 30 seconds, Sound Synchronized Recording will stop. "WRITING" appears in the display window, and you can remove the MD by pressing 0 (eject) button. 3 Recording onto a Tape You can record an MD onto a tape manually and using the recording mode feature. · For details on recording operation of TD-UXG6 cassette deck, refer to UX-G6R's Instructions (pages 26 ­ 28). 4 Recording an MD onto a tape manually Press SET button to start recording. Recording the MD onto the tape starts, and information appears in the display window as follows: Track number Elapsed playback time 1 2 Insert an MD to be played-back into the loading slot, and load a recordable tape. Press 6 (play/pause) button on the MD recorder or MD 6 (play/pause) button on the remote control, then press 7 (stop) button immediately to prepare playing back the MD. Press REC PAUSE button on TD-UXG6 cassette deck to prepare for recording. [. . . ] The remaining time on the MD does not increase even when tracks are erased. The sound drops out during fast forward or fast rewind. Cause There is a maximum number of tracks which can be recorded, regardless of recording time. More than 254 tracks cannot be recorded on an MD. [. . . ]