User manual JVC XU-301

[. . . ] MD-CD COMBINATION DECK PLATINE COMBINÉE MD-CD XU-301BK XU-301 MD-CD COMBINATION DECK 32kHz DIGITAL INPUT 44. 1kHz 48kHz EDIT TITLE DISPLAY /CHARA PLAY MODE CD 3 2 CD CD 1 PLAY & EXCHANGE 3-CD MIXING REC PAUSE REC START REC STOP DIGITAL CD LINE MIC CANCEL SET REC SOURCE SELECTOR STANDBY TIMER CD PITCH CONTROL /CLOCK MIX BALANCE 1st TRACK REC LISTENING EDIT CD REC LEVEL POWER NORMAL SPEED CD REC SKIP MD LINE MIC CD LINE MIN MAX MIC PHONES SAMPLING RATE CONVERTER INSTRUCTIONS MANUEL D'INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0009-001B [J] Warnings, Cautions and Others/Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN To reduce the risk of electrical shocks, fire, etc. : 1. [. . . ] Press the REC STOP button to stop the recording at any time. · DIGITAL INPUT lamps These lamps light as follows in the rec pause or recording mode. · DIGITAL : 32 kHz­48 kHz lights depending on the sampling frequency of the recording source. · CD : 44. 1 kHz lights 28 When DIGITAL IN UNLOCK is scrolled and displayed, the OPTICAL IN connector is not connected to the source unit. In the case of an MD with some remaining space, the end of the last track recorded is automatically searched, and recording is commenced immediately. To record over all the existing tracks, erase all the tracks using the ALL ERASE function (see page 40), and then proceed with the new recordings. Upon completion of the MD recording, "UTOC WRITING" is displayed. Operating any button while this message is displayed may render the MD unusable. Always wait for "UTOC WRITING" to be cleared before proceeding with the next operation. When digital input signals are supplied, they will be recorded in their original digital form. There is no need to adjust their recording level. CD Recording (single-action recording) CD play and MD recording are started simultaneously. 3 XU-301 MD-CD COMBINATION DECK 1 -1 32kHz 2 DIGITAL INPUT 44. 1kHz 48kHz 1 -2 EDIT TITLE DISPLAY /CHARA PLAY MODE CD 3 2 1 PLAY & EXCHANGE CD CD 3-CD MIXING REC PAUSE REC START REC STOP DIGITAL CD LINE MIC CANCEL SET REC SOURCE SELECTOR STANDBY TIMER CD PITCH CONTROL /CLOCK MIX BALANCE 1st TRACK REC LISTENING EDIT CD REC LEVEL POWER NORMAL SPEED CD REC SKIP MD LINE MIC CD LINE MIN MAX MIC PHONES SAMPLING RATE CONVERTER 1 Select and stop the CD to be recorded. Example: When recording CD1 · Only the selected CD is recorded. 2 Insert the recording MD. · CD REC Insert the MD with its label side facing up. CD play and MD recording start simultaneously. Recording starts from track 1. Remaining play time of track being recorded Remaining recording time on MD 3 Press the CD REC button to start the recording. · CD MD DIGITAL L R 40 30 20 15 10 6 3 0 TOC REC "DIGITAL" is displayed. · When a CD is recorded, its digital signals are recorded in their original form. A track mark is automatically placed where one track changes to the next, and the track number also changes. · When MD recording is completed After "UTOC WRITING" is displayed, operation stops automatically. It also stops automatically when CD play finishes. CD play is transferred to the next tray. · To check a track number during recording Main unit DISPLAY /CHARA Remote control Press DISPLAY/CHARA button (or DISPLAY MODE on the remote control). \ Remaining time of track being recorded « CD number and track number MD track number Remaining recording time on MD The mode changes each time this is pressed. 29 English · To stop the recording at any time English Press the 7 (stop) button. The recording mode is released after "UTOC WRITING" is displayed. There is no need to adjust the recording level (for a digital recording). Recording is not possible while a CD or MD is playing. When the CD REC button is pressed, the function is automatically switched to "CD. " This means that when the CD to be recorded has been selected, recording can proceed straightaway. Upon completion of the MD recording, "UTOC WRITING" is displayed. Operating any button while this message is displayed may render the MD unusable. Always wait for "UTOC WRITING" to be cleared before proceeding with the next operation. CD Recording (1st TRACK recording) Only the first tracks on the CDs can be recorded on the MD. 4 XU-301 MD-CD COMBINATION DECK 1 2 -1 3 32kHz DIGITAL INPUT 44. 1kHz 48kHz 2 -2 EDIT TITLE DISPLAY /CHARA PLAY MODE CD 3 2 1 PLAY & EXCHANGE CD CD 3-CD MIXING REC PAUSE REC START REC STOP DIGITAL CD LINE MIC CANCEL SET REC SOURCE SELECTOR STANDBY TIMER CD PITCH CONTROL /CLOCK MIX BALANCE 1st TRACK REC LISTENING EDIT CD REC LEVEL POWER NORMAL SPEED CD REC SKIP MD LINE MIC CD LINE MIN MAX MIC PHONES SAMPLING RATE CONVERTER 1 Insert CDs into CD1, CD2 and CD3 in the order in which their first tracks are to be recorded. · Once the first track of a CD has been recorded, another track on that CD can be substituted during recording. [. . . ] This unit is designed to comply with this restriction. OK DIGITAL DIGITAL NO The copyright laws allow recordings to be made for the personal enjoyment of the individual user but they do not allow such recordings to be used for other any purposes without permission from the holder of the copyrights. MDs on which CD sound has been recorded using this unit cannot be digitally copied by other units. 54 Symptom COMMON No sound. Cause Remedial action/check Ref. 20 45-47 12 · An MD with nothing recorded on it has been · Replace the MD on which tracks have been inserted. ("BLANK DISC" is displayed. ) recorded. · Set the clock and re-program the timer. · Insert it properly with the label side facing up. [. . . ]