User manual JVC XV-565

[. . . ] DVD VIDEO PLAYER XV-M565BK/XV-M567GD Introduction 1 Preliminary knowledge 4 Getting started 12 Basic operations 17 CHOICE DISC 1 TV POWER DISC 2 DISC 3 DVD POWER SUBTITLE AUDIO ANGLE DISPLAY Advanced operations DVD PLAYER SHUTTLE 21 DIGEST STROBE ZOOM TIME 1 TV 1 2 TV 2 3 TV 3 4 TV 4 5 TV 5 6 TV 6 7 TV 7 8 TV 8 9 TV 9 10 TV RETURN 0 TV 0 +10 TV 100+ SLOW AMP VOL TV VOL TV ch PLAY MODE RETURN TV/VIDEO POWER SHIFT CANCEL STANDBY DIGEST DVD 3 2 1 STOP PAUSE 3 2 1 PLAY H B. SEARC B. SKIP PLAY 3D PHONIC THEATER POSITION F. SEARC H F. SKIP STROBE DVD PAUSE STOP ENTE MENU ZOOM R DVD Initial settings DVD / VIDEO CD / CD 36 TITLE UP LEFT CURSOR THEATER POSITION DISC TITLE CHAP RESUME THEATER DVD EACH DOLBY DIMMER RIGHT SKIP DOWN PLAY & EXCHANGE DIGITAL 3D PHONIC REMOTE CONTROL ' INSTRUCTIONS Additional information 42 For Customer Use: Enter below the Model No. which are located on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0521-001A [J] Warnings, Cautions and Others Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electrical shocks, fire, etc. : 1. [. . . ] In both cases above, the unit basically plays back all discs in the trays once continuously in the following sequence and then stops. PAUSE STOP ENTE MENU R TITLE UP LEFT CURSOR Basic control buttons RIGHT DOWN DISC1 DISC2 DISC3 REMOTE CONTROL NOTES · The 1 through 3 buttons on the front panel function the same as the DISC 1 through 3 buttons on the remote control unit respectively. · When the resume point is memorized, pressing PLAY starts playback from that point instead of the beginning. · During playback, the display window shows the disc number and the title/chapter or track number being played. · With Video CD discs with PBC control or some DVD discs, the menu display may appear on the TV screen after starting playback. In such a case, select an item to be played back from the menu. For operation using a menu, see page 21. · With some DVD discs, the unit starts playback automatically after inserting the disc. To stop playback completely Press STOP. The unit stops playback. To stop playback temporarily Press PAUSE. The unit pauses playback. To continue playback, press PLAY. 18 Basic operations · The unit changes the playback disc when the current disc finishes and stops playback. Therefore, if the current disc is a DVD VIDEO disc or a Video CD disc with PBC function, it may not finish playback and the unit may not change the disc and playback the next disc. Basic operations To advance or reverse playback rapidly while monitoring 7 During playback From the remote control unit Hold down 4 or ¢. Holding down ¢ advances playback rapidly, while holding down 4 reverses playback at 5 times the normal speed. Releasing the button returns the unit to normal playback. or Press 4 or ¢ while holding down the SHIFT button. Each press of 4 or ¢ while holding down the SHIFT button increases the playback speed from 2x to 60x the normal speed. Pressing PLAY returns the unit to normal playback. From the front panel Use the SHUTTLE knob. To advance playback rapidly, turn the shuttle knob to the right and hold, and to reverse play rapidly, turn the shuttle knob to the left and hold. By releasing the shuttle knob, the unit returns to normal playback. The playback speed changes according to the amount you turn the shuttle knob. 3 SHUTTLE knob SHUTTLE 3 2 1 STOP PAUSE DIMMER DISC TITLE CHAP DVD EACH PLAY RESUME THEATER SKIP C DVD / VIDEO CD / CD Basic operations Holding down the 4 or ¢ button on the front panel also advances or reverses playback rapidly. To locate the beginning of the scene or song 7 During playback Press 4 or ¢. Press 4 to locate the beginning of the current chapter, title, or track, and press ¢ to locate the beginning of the next chapter, title, or track. NOTE · When you play a Video CD disc with the PBC function or a DVD VIDEO disc, the unit may locate a different place, but it will generally locate the beginning of the title, chapter or track. 19 Basic operations Resuming playback The unit can memorize the position on a disc where you interrupt playback, and resume playback from that position next time you press PLAY. English Français To memorize the interrupted position 1 2 Set the RESUME setting on the SYSTEM page of the preference display to ON. (See page 39 for details about how to set. ) At the position you want to interrupt playback, press STOP, or press DVD POWER - TV POWER on the remote control or POWER on the front panel. The unit memorizes the interrupted position, while [RESUME] lights in the display window. If you interrupt playback by pressing STOP in step 2 above and then turn off the power, the memory is not cleared. To resume playback 7 While the disc you interrupt playback last time is still in the disc tray. The unit starts playback from the position where you interrupted playback last time. ¶ To clear the resume position memory Carry out one of the following: * Take out the disc from the tray. * Turn on the unit by pressing DVD POWER - TV POWER (on the remote control) or POWER (on the front panel). NOTES · If you want to resume playback, do not press a DISC (1 - 3) button to start playback or do not press the POWER (on the front panel) or DVD POWER - TV POWER (on the remote control) to turn on the unit. · The resume function does not work with Audio CD discs. · The resume function does not work if RESUME on the SYSTEM page of the preference display is set to OFF. · In the case of a Video CD disc with PBC function, the unit may resume playback from a point slightly earlier than the resume point you stored. · The resume function does not work in the program or random mode. 20 Basic operations Press PLAY. Advanced operations Advanced operations NOTES · When step 1: appears on the TV screen by pressing TITLE in When you use the functions described below while stopped, make sure that the desired disc number is selected (the selected disc number is shown in the display window). If it is not selected, press the corresponding DISC button to start playback and then press STOP. The disc does not have a menu listing the titles. [. . . ] WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800)537-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. If you have any questions concerning your JVC Product, please contact our Customer Relations Department. [. . . ]