User manual JVC XV-N5

[. . . ] DVD PLAYER XV-N5SL Introduction 2 Getting started 6 Basic operations 12 Advanced operations TV OPEN/ CLOSE TV DVD DVD 23 STANDBY/ON TV1 TV2 TV3 1 TV4 2 TV5 3 TV6 4 TV7 5 TV8 6 TV9 7 TV-/-- 8 TV0 9 MUTING 10 RETURN 0 SUBTITLE TITLE/ GROUP +10 TV/VIDEO CANCEL MP3 disc playback 40 T OP U CH MEN + MEN U VOL+ VOL- ENTER CH OIC E N CH - PREVIOUS E RE SC ON NEXT CLEAR SELECT STROBE SLOW- SLOW+ XV-N5 REPEAT SUB TITLE AUDIO VFP DIGEST 3D PHONIC ANGLE ZOOM DVD/SUPER VCD/VCD/CD PLAYER AMP VOL JPEG disc playback 43 RM-SXV009E REMOTE CONTROL VIDEO Changing the initial settings 48 INSTRUCTIONS Additional information 57 LET0204-004A [B] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. BE SURE to replace the fuse only with an identical approved type, as originally fitted. [. . . ] While zoomed in, an indication of the zoomed image position also is displayed. The next step can be used to move the image position. 2 Use 5//2/3 to move the zoomed position. If no button pressed for 5 seconds, the information for the current magnification disappears. To display the information, press ZOOM +/­ or 5// 2/3 again. ZOOM x 4 33 Advanced operations ¶ During playback Advanced operations NOTES · To return to normal playback. · While zoomed, the picture may look coarse. 3 To define a user setting, select a parameter to be edited using 5/ from the following. · GAMMA Controls the brightness of a shaded portion without changing the brightness of the entire picture. This control is optimum when you adjust the pictures of software which generates subdued black in a bright room. · BRIGHTNESS Controls the brightness of the screen. · CONTRAST Controls the contrast of the screen. · SATURATION Controls the color depth of the screen. · TINT Controls the tint of the screen. Use the appearance of a natural skin tone as a guideline. · SHARPNESS Controls the sharpness of the screen. · Y DELAY Controls the color gap of the screen. The setting range is +2 to -2. To adjust the picture character [VFP] Available : The VFP (Video Fine Processor) function allows you to adjust the picture character according to the type of programming, picture tone or personal preferences. TV OPEN/ CLOSE TV DVD DVD STANDBY/ON TV1 TV2 TV3 1 TV4 2 TV5 3 TV6 4 TV7 5 TV8 6 TV9 7 TV-/-- 8 TV0 9 MUTING 10 RETURN 0 SUBTITLE TITLE/ GROUP +10 TV/VIDEO CANCEL T OP NU CH ME + ME NU VOL+ ENTER VOL- ENTER CH OIC E 5//2/3 CH - PREVIOUS ON NEXT EN RE SC CLEAR SELECT STROBE SLOW- SLOW+ REPEAT SUB TITLE AUDIO VFP VFP DIGEST ANGLE ZOOM Advanced operations 3D PHONIC AMP VOL RM-SXV009E REMOTE CONTROL ¶ During playback 1 Press VFP. The VFP mode selection window appears on the TV screen. 4 Press ENTER. A window for setting parameters appears instead of the VFP mode selection window. 2 Use 2/3 to select the desired preset. Each time you press the button, the VFP mode changes as follows. Set the video type most suitable to the current program or the room conditions. Selected preset SATURATION +45 NORMAL USER 1 GAMMA BRIGHTNESS CONTRAST SATURATION TINT SHARPNESS Y DELAY +4 +4 +13 +13 +13 +4 +2 Selected parameter CINEMA USER 1 5 Adjust the level of the parameter using 5/. The higher value enhances the effect. 6 Press ENTER. The parameter is set and the VFP mode selection window appears again. Repeat steps 3 to 6 if you want to set other parameters. Parameter USER 2 "NORMAL" is suitable for watching TV in a general room. "CINEMA" is suitable for watching a movie software in a room with suppressed light. They are factory presets and you cannot change parameters for them. If you select "USER 1" or "USER 2, " you can adjust parameters that affect the picture character and store the settings as a user preset. See the next step. 34 Advanced operations NOTES · The number of setting steps varies for different parameters. · To dismiss the VFP mode selection window: Press VFP . · The window for VFP mode selection and parameter setting disappears if no operation is made for about 10 seconds. 3 Press 5/ to adjust the effect level. You can set the effect level from "1" to "5. " The higher value enhances the effect. ACTION +45 To simulate surround sound [3D PHONIC] Available : Using the 3D PHONIC function, you can get a simulated surround effect from your stereo system. TV OPEN/ CLOSE TV DVD DVD Effect level . NOTES · To dismiss the 3D PHONIC window: Press 3D PHONIC. [. . . ] Used on Super VHS, DVD, high end TV monitors, etc. Title The largest division on DVD VIDEO. Track The smallest division on Audio CD, Video CD and SVCD discs. Transfer rate The rate of transferring digital data. [. . . ]