User manual JVC XVN55SL-XV-N55 Instruction Manual

[. . . ] HOME CINEMA CONTROL CENTER DVD VIDEO PLAYER RX-ES1SL XV-N55SL INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT1002-001B [B] Warnings, Cautions and Others IMPORTANT for the U. K. [. . . ] For selecting Panorama control for Pro Logic II Music, use the buttons on the front panel. 1 Select and play software you like. Surround Surround Surround Surround 2 Press SURROUND to select an appropriate Surround mode. Available Surround modes: PL II MOVIE (Pro Logic II MOVIE) PL II MUSIC (Pro Logic II MUSIC) Available DSP modes: LIVE CLUB DANCE CLUB HALL PAVILION ALL CH ST. (All Channel Stereo) Each time you press the button, the Surround/DSP modes change as follow: When playing back multi-channel digital software such as Dolby Digital or DTS Digital Surround: L DOLBY D LS RS VOL C R SUBWFR LFE DOLBY D or DTS STEREO (Surround/DSP off) When connecting 3 speakers Front TV Center Front When playing back 2 channel digital software such as Dolby Digital or DTS Digital Surround: PL II MOVIE PL II MUSIC STEREO (Surround/DSP off) When playing back any software other than above: Available Surround modes: PL II MOVIE (Pro Logic II MOVIE) PL II MUSIC (Pro Logic II MUSIC) PL II MOVIE LIVE CLUB HALL ALL CH ST. (Back to the beginning) PL II MUSIC DANCE CLUB PAVILION STEREO (Surround/DSP off) NOTE When "AUTO SR (Auto Surround)" is turned "ON" (see page 20), Surround mode is automatically activated when you select and start playing back a multi-channel digital source. If "AUTO SR (Auto Surround)" is set to "ON" Playing a digital source automatically activates an appropriate Surround mode. (See page 20. ) Go to step 3. 30 Creating realistic sound fields 3 Press TEST to check the speakers output balance. "TEST L" starts flashing on the display, and a test tone comes out of the speakers as follow: L LPCM SUBWFR VOL R PL On the front panel: No test tone is available when using the buttons on the front panel. There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again. TV DIRECT SETTING ADJUST SURROUND SET / TUNER PRESET SOURCE SELECTOR / MULTI JOG MASTER VOLUME PHONES STANDBY / ON STANDBY DVD MULTI DVD STB VCB TV FM / AM (Left front speaker) (Center speaker) (Right front speaker) (Left surround speaker) (Right surround speaker) TEST L TEST C TEST R TEST LS TEST RS 1 Select and play software you like. 2 Press SURROUND. MULTI JOG now works for the Surround/DSP mode selection. 4 Adjust the following speaker output levels (from 10 dB to +10 dB). Make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers. To adjust the center speaker level, press CENTER +/. To adjust the left surround speaker level, press SURR L +/. To adjust the right surround speaker level, press SURR R +/. L LPCM SUBWFR VOL R PL 3 Turn MULTI JOG to select a appropriate surround mode. As you turn MULTI JOG, the indication changes as follow: When playing back multi-channel digital software such as Dolby Digital or DTS Digital Surround: L DOLBY D LS RS VOL C R SUBWFR LFE Ex. : When selecting "+8 (dB)" for "CENTER. " DOLBY D or DTS STEREO (Surround/DSP off) 5 Press TEST again to stop the test tone. The currently selected source name appears on the display. When playing back 2 channel digital software such as Dolby Digital or DTS Digital Surround: PL II MOVIE PL II MUSIC STEREO (Surround/DSP off) When playing back any software other than above: PL II MOVIE LIVE CLUB HALL ALL CH ST. (Back to the beginning) PL II MUSIC DANCE CLUB PAVILION STEREO (Surround/DSP off) If "AUTO SR (Auto Surround)" is set to "ON" Playing a digital source automatically activates an appropriate Surround mode. (See page 20. ) Go to step 3. 4 Press ADJUST. MULTI JOG now works for the sound adjustment. 5 Turn MULTI JOG until the setting item you want to set appears on the display, then press SET. As you turn MULTI JOG, the indication changes as follow: L LPCM SUBWFR VOL R PL BASS CENTER EFFECT B. BOOST SUBWFR TREBLE SURR L SURR R BAL PANORAMA* (Back to the beginning) ATT * Available only for "PL II MUSIC. " CONTINUED ON THE NEXT PAGE 31 Creating realistic sound fields CENTER*1: SURR L*1: SURR R*1: To adjust the center speaker output level (from 10 dB to +10 dB). To adjust the left surround speaker output level (from 10 dB to +10 dB). To adjust the right surround speaker output level (from 10 dB to +10 dB). Using DSP modes Once you have adjusted the DSP modes, the adjustment is memorized for each source. You cannot use the DSP modes if no surround speakers are connected. You cannot adjust the effect level for "ALL CH ST. " When operating this receiver using the remote control, always set the mode selector to AUDIO/TV/VCR/STB. DVD AUDIO/TV /VCR/STB PANORAMA control*2: Select "ON" when you would like to enjoy "wraparound" sound effect with side-wall image. Select "OFF" when you would like to hear originally recorded sound. *1 "0" is the initial setting for each speaker setting. *2 "OFF" is the initial setting. Before you start, remember. . . Make sure that you have set the speaker information correctly (see pages 15 to 18). 6 Turn MULTI JOG to adjust the item selected in step 2, then press SET. Your setting is stored. When adjusting the speaker output levels, make adjustments so that the sound level of the selected speaker is set at the same level as that of the front speakers. L LPCM SUBWFR VOL R PL From the remote control: AUDIO SUBTITLE TITLE/GROUP RETURN ZOOM BASS TREBLE 1 VFP 2 BASS 3 TREBLE 4 7 5 8 0 6 9 100+ ANGLE TV RETURN 10 REPEAT +10 3D DIMMER SLEEP ANALOG/DIGITAL CANCEL INPUT A. POSITION TONE SURROUND DECODE EFFECT CENTER L SURR R It will be convenient for you to use the remote control for the sound adjustments, since you can make adjustments from your listening point, and use the test signal. SMART S. SETUP BASS BOOST TEST SUBWFR Ex. : When selecting "+8 (dB)" for "CENTER. " 7 Repeat steps 5 and 6 to adjust the other settings. 1 Start playing 2 channel software--either Linear PCM or analogue signal--and select the source. To cancel Surround mode Press SURROUND repeatedly on the remote control or press SURROUND then turn MULTI JOG on the front panel so that "STEREO" appears on the display. If Surround mode is canceled while playing back multi-channel digital software, all channel signals are mixed and output through the front speakers (and subwoofer if you have connected a subwoofer and set the subwoofer setting correctly--"USE" for Quick Setup or "YES" for Manual Setup--see pages 16 and 17). 2 Press SURROUND repeatedly until one of the DSP modes you want to apply appears on the display. The DSP indicator lights up on the display. [. . . ] Turn off the power and unplug the power cord, then connect the power cord again. Turn off the power, then turn it on a few hours later. Check and replace the disc (see page 35). When you press 0 while pressing down 7 The disc tray cannot be opened or closed in this on the player in standby mode, the tray status. To release this status, press 0 while pressing lock function is activated. The player is connected to a VCR directly and the copyguard function is activated. [. . . ]