User manual JWIN JX-CD8500

[. . . ] JX-CD8500 STEREO HI-FI SYSTEM with 4 CD CHANGER / MP3 and AM/FM PLL SYNTHESIZED TUNER OWNER'S MANUAL JXCD8500V10M11EN05022005 PRECAUTIONS WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PRESENT BLADE EXPOSURE. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: To avoid electric shock, this unit must not be exposed to dripping or splashing water Minimum distances around the apparatus for sufficient ventilation; The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths curtains, etc. No naked flame sources, such as lighted candles, should be placed on the apparatus; Before scrapping the appliance, remove the batteries and place them in the appropriate battery collection container. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock persons. Warning: to reduce the risk of electric shock, do not remove cover (or back) no user-serviceable parts inside. [. . . ] Store any remaining stations by repeating the process. Changing a program position If a memory position needs to be replaced by a station other than the current one, the new station can be programmed as described above, and will replace the original station. Manual station selection Press button "TUNER / BAND" (7)/(53) repeatedly until the desired frequency band appears. Press the buttons "TUNING - or TUNING +" (20)/(43) or (18)/ (41) to tune to the desired radio stations and have them indicated in display (3). Briefly tapping the button "TUNING - or TUNING +" step by step alters the reception frequency upward or downward. The right and left CD cover do not opened or closed at the same time. Make sure the cover is not obstructed by any objects. This must also be ensured when closing the CD cover. The disc loader may only be opened or closed by pressing either the button "OPEN / CLOSE". Take care that no foreign objects can fall into the unit when the disc compartment is open. Under no circumstance should the laser pick up lens be touched. CD changer operation Switch the unit on by pressing the "POWER" button (1)/(32). To turn on the CD mode, press the button " PLAY / PAUSE" (13)/(38) or any one of the DISC 1-4 buttons (5) or (49). If one or more CD(s) have already been inserted in the chosen location(s), playback is started. Playing the entire CD Select the desired CD with the button "CD SELECTION 1 - 4" (5) or "DISC 1 - 4" (49) on the remote. Then close the disc compartment by pressing the "OPEN / CLOSE" button (15) or (16). After having closed the disc cover, the CD system immediately begins to scan the content of the compact disc. Subsequently, the number of tracks and the play-back time of the compact disc occupying position 1 appear in the display unit (3). To set the clock to the current time proceed as follows: 1. Enter the hour by pressing the buttons TUNING + SKIP/SEARCH or TUNING - SKIP/SEARCH. Confirm the entry by pressing MEM. /CLK ADJ. Enter the minutes by pressing the buttons TUNING + SKIP/SEARCH or TUNING - SKIP/SEARCH and confirm with MEM. /CLK ADJ. Set the switch-off time using the same procedure as switch-on time setting. Press DISPLAY MODE, as required to check the current time, Timer On, and Timer Off. [. . . ] To clear the programming (Resume Normal Playback): The programming is erased by pressing the " STOP" button (11)/(45) in the programming mode (until the MEMORY display disappears), or by opening the disc compartment. Press the "REPEAT" button again to have the entire MP3 disc played continuously. Pause / stop To briefly pause playback, press the " PLAY / PAUSE" button (13)/(38). Press the "MEM. /CLK ADJ. " (9)/(50) to save the title on the first program location. In display unit (3) appears: Note: REPEAT button (12)/(47) is not used for programming. ID3 TAG (Artist/Title) Press the "REPEAT" button again to have all the inserted MP3 discs played continuously. When an MP3 disc is playing, press the "MP3 MODE" button repeatedly. [. . . ]