User manual KARCHER SE 2001

[. . . ] Turn the cleaner off with the switch button before removing from the mains outlet. Always remove the plug from a mains outlet before carrying out any maintenance. Do not carry out any maintenance work on the cleaner other than that outlined in this manual, especially where electrical components are concerned. Do not use without the clear bin assembly fitted correctly and both filters in place. [. . . ] Do not continue to use the cleaner if any part appears to be faulty, missing or damaged. In these cases, contact the Dyson Helpline on 01666 827272. Do not put any part of the body, clothes or any object near or into the openings or moving parts of the machine. Do not use the machine with any of the openings blocked with any object that may restrict the airflow. Do not pull on the supply cord, run over it or pull it around sharp edges or near/over hot surfaces. Do not handle the cleaner or plug with wet hands. Do not use the cleaner if the cord or plug are damaged or if the cleaner has been damaged, dropped or has come into contact with water or any other liquid. Do not use the cleaner to pick up water or any other liquid. Electrical shocks could occur if used outdoors or on wet surfaces. IMPORTANT A LWAY S U N P L U G T H E VAC U U M C L E A N E R F R O M T H E WA L L S O C K E T B E F O R E I N S P E C T I N G I T NOTE Check that your supply corresponds to that shown on the rating plate. The appliance must only be used as rated, it should be fitted with an ASTA approved fuse to BS1362. European conformity information A sample of this product has been tested and found to be in conformity with the following European Directives: 73/23/EEC Low voltage (safety) Directive, 93/68/EEC CE Marketing Directive and 89/336/EEC EMC Directive. These are entirely harmless and are not associated with the mains supply. To minimise any effect from this, do not put your hand or insert any object into the clear bin unless you have first emptied and rinsed out the clear bin with water. 4. 5. 6. 7. KARCHER CUSTOMER CARE KARCHER CUSTOMER CARE Helpline 01666 827272 T ET B U RY HILL Helpline 01666 827272 T ET B U RY HILL Facsimile 01666 827298 Contact for all service assistance MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P Facsimile 01666 827298 Contact for all service assistance MALMESBURY W I LTS H I R E EN G L AN D S N 16 O R P 03-28-208 05-28-055 14/02/97 REV 1 1 Changing filters Your DCO2 is fitted with two high area H-level electrostatic cartridge filters. Alternatively a standard S-level filter may be purchased. m ax m ax 2 1 Insert top filter ensuring that it fits snugly against the black rubber seal on the machine. 2 Slide rear filter into the grooves and push it down fully. Fitting instructions for the standard S-level filters are printed on the filter itself. H H-Level S-Level S Clear bin full mark Note: Do not fill above this line. 2 H-level OR 1 S-level 2 Automatic suction control trigger Hold the yellow trigger down to reduce suction for upholstery and curtains. 2. Clear bin removal IMPORTANT Use only genuine Dyson filters. To maintain reduced suction, press the trigger down hard until it clicks. To unlock and resume full suction, press down the opposite end of the trigger. Sits securely on the stairs However, always work above the machine on stairs for your own safety. Telescopic wand click 3 Press yellow button and slide wand down to adjust length. Blockage procedure Please note: Any `Blockage only' repairs will incur a charge of £35. 00 *. Check filters, replace if older than 3 months, or if filters are heavily coated with dust. 1 To empty clear bin, pull back release catch under carrying handle and raise top of machine. 1 *Price correct at time of printing. 2 Lift clear bin out of machine. 1 1. Check entry swivel by pressing yellow buttons & pulling out hose. Clear any debris. 3 Remove cyclone top (lid). 1 The plug is situated underneath the tool cover on the right hand side. 1. Hose & wand assembly Assemble hose and wand by fitting 3 together at joints 1 , , and . [. . . ] Press buttons and pull hose to release. 2 2. Check wand handle swivel 2 by pressing yellow buttons and pulling hose from wand. Clear any debris. On/off switch Press left switch. Tool storage Press yellow release catch to open the tool storage cover and insert required tool into end of wand or wand handle. Please note that tools may feel warm when machine has been running; this is perfectly normal. Wand handle Wand Self adjusting Floor tool Fit floor tool by pushing firmly into end of wand. 3. [. . . ]